|
FM2A88X PRO3+ sensors not working in Ubuntu 15.10 |
Post Reply 
|
| Author | |
wardog 
Moderator Group 
Joined: 15 Jul 2015 Status: Offline Points: 6447 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: FM2A88X PRO3+ sensors not working in Ubuntu 15.10Posted: 23 Nov 2015 at 6:55pm |
|
You can ask ASRock Tech Support through the asrock.com website.
|
|
 |
|
|
highball
Newbie 
Joined: 22 Nov 2015 Status: Offline Points: 9 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 Nov 2015 at 9:22pm |
|
I have found this before... But this means they will NOT work without the help of AsRock to support in defining GPIO adresses needed to be configured...
Does anyone here know what needs t be configured...? Is someone from AsRock around here that may help? Thanks and best regards Jens
|
|
|
|
|
wardog
Moderator Group
Joined: 15 Jul 2015 Status: Offline Points: 6447 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 Nov 2015 at 9:17pm |
|
http://comments.gmane.org/gmane.linux.drivers.sensors/38139
|
|
|
|
|
highball
Newbie
Joined: 22 Nov 2015 Status: Offline Points: 9 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 Nov 2015 at 8:13pm |
|
sensor-detect was right... NCT5573D is on my MB....
This does actually not help... correct module, but does not work :-( Perhaps I need a special configuration? Does anyone can help me? Thanks and best regards Jens
|
|
|
|
|
wardog
Moderator Group
Joined: 15 Jul 2015 Status: Offline Points: 6447 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 Nov 2015 at 10:50am |
|
Jens, take the fun out of letting Ubuntu guess it and read exactly what sensor chip your board uses by looking at it directly, between the start of PCIE4 and the edge of the board. Below where your BIOS chip resides.
|
|
|
|
|
highball
Newbie
Joined: 22 Nov 2015 Status: Offline Points: 9 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 Nov 2015 at 7:31am |
|
Hello!
I have a question regarding my AsRock FM2A88X PRO3+... I actually use this MB with Ubuntu 15.10 Server and try to get the sensors working... I have found out the it uses the following sensors: Driver `nct6775': * ISA bus, address 0x290 Chip `Nuvoton NCT5573D/NCT5577D/NCT6776F Super IO Sensors' (confidence: 9) Driver `k10temp' (autoloaded): * Chip `AMD Family 15h thermal sensors' (confidence: 9) But the problem is, that I do not see any correct data calling "sensors": radeon-pci-0008 Adapter: PCI adapter temp1: -5.0°C (crit = +120.0°C, hyst = +90.0°C) nct6776-isa-0290 Adapter: ISA adapter Vcore: +0.94 V (min = +0.00 V, max = +1.74 V) in1: +0.18 V (min = +0.00 V, max = +0.00 V) ALARM AVCC: +3.33 V (min = +2.98 V, max = +3.63 V) +3.3V: +3.31 V (min = +2.98 V, max = +3.63 V) in4: +0.47 V (min = +0.00 V, max = +0.00 V) ALARM in5: +1.69 V (min = +0.00 V, max = +0.00 V) ALARM in6: +1.83 V (min = +0.00 V, max = +0.00 V) ALARM 3VSB: +3.41 V (min = +2.98 V, max = +3.63 V) Vbat: +3.38 V (min = +2.70 V, max = +3.63 V) fan1: 763 RPM (min = 0 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 0 RPM (min = 0 RPM) fan5: 0 RPM (min = 0 RPM) SYSTIN: +26.0°C (high = +0.0°C, hyst = +0.0°C) ALARM sensor = thermistor CPUTIN: +30.0°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor AUXTIN: -25.5°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor PCH_CHIP_TEMP: +0.0°C PCH_CPU_TEMP: +0.0°C PCH_MCH_TEMP: +0.0°C intrusion0: OK intrusion1: OK beep_enable: disabled k10temp-pci-00c3 Adapter: PCI adapter temp1: +0.0°C (high = +70.0°C) (crit = +70.0°C, hyst = +69.0°C) fam15h_power-pci-00c4 Adapter: PCI adapter power1: N/A (crit = 65.19 W) Can some give me a hint what I have to do to see all Fans, Temps and Voltages here?! By the way, I can see all CORRECT values in BIOS... Thanks and best regards from Germany :-) Jens Edited by highball - 22 Nov 2015 at 7:54am |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options