|
New Z170 Build Randomly locking up - ALSO |
Post Reply 
|
| Author | |
Basalt 
Newbie 
Joined: 29 Feb 2016 Status: Offline Points: 7 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: New Z170 Build Randomly locking up - ALSOPosted: 29 Feb 2016 at 8:56am |
|
Just built this. Having random lockups, some I worked around. ASRock Fatal1ty Z170 i7 mobo BIOS P1.60 4 stick kit HyperX 32gb kit 22666 i5-6600k Samsung 950Pro for a boot drive EVGA GTX980 Win 10 Pro. booted up and was surprised it immediately went to installing windows without any nudging on my part. all is fine, ram even auto set correctly. To good to be true I think. Yep have this occasional lock up for no apparent reason. First it was locking up trying to update the nic. worked around that, then it started while installing software or surfing the net. finally the Bios freezes up for no apparent reason while I am looking through the options. hard lock, power down to recover. I am unable to load the ME driver update to 11.0.0.1172 also. I am aware of the Z170 freeze bug but am hoping the BIOS update already accounted for that. Considered the PSU but I swapped out, didn't help. Could be missing something in UEFI, I just switched over from Gigabyte, so it is a tad foreign to me. |
|
 |
|
|
GripS
Newbie
Joined: 23 Jan 2016 Status: Offline Points: 21 |
Post Options
Thanks(0)
Quote Reply
Posted: 29 Feb 2016 at 11:11am |
|
Which variant of the motherboard are you running? 1.60 sounds old to start with. I would run with default BIOS settings and make sure you update to the latest version. If you are running your ram with XMP profile, don't. If it's stable after that, you need to look into possibly manually raising VCCIO and VCCSA voltages to get rated speeds with XMP profile set. This was definitely the case in my build (Z170 Gaming K6). Try just manually setting the voltages for those two values manually at their recommended setting, which should show to the left of 'auto' after setting XMP and rebooting. So basically set them manually to match the left side (not sure why this works but it did for me). In my case VCCIO is 1.10 and VCCSA is 1.15. Hopefully i'm making sense.
Nevermind about the variant. I see that it is the Fatal1ty i7. 1.60 is the latest for that board. Try manually seeing the voltages though as I suggested. Edited by GripS - 29 Feb 2016 at 11:12am |
|
|
|
|
netjrb
Newbie
Joined: 09 Feb 2016 Status: Offline Points: 15 |
Post Options
Thanks(0)
Quote Reply
Posted: 29 Feb 2016 at 1:37pm |
|
Do you have an optical drive on an Asmedia Sata port? That was causing random lock ups on my system.
|
|
|
|
|
Basalt
Newbie
Joined: 29 Feb 2016 Status: Offline Points: 7 |
Post Options
Thanks(0)
Quote Reply
Posted: 29 Feb 2016 at 10:13pm |
|
yes P1.60 is the latest, I am curious if it has the same freeze bug fix as 1.5, my bios rev was 1.0 so I guess the board has been on the shelve for a while.
Noted about voltages, going to be a few hours before I can get home to try, however the freeze ups in BIOS seriously hinder me. Ram is 1.2 rated, but set to 1.25 currently, I'll disable the XMP profiles and set to default. It actually surprised me when it automatically set to XPD. The more I think about it the more I am wondering about voltages in general, the CPU voltage seemed a tad low as well, but again, the BIOS freezes up when I start trying to make adjustments, and even if I get through to the save point, it goes back to default. I'll see if I can manually set the voltages you suggested. |
|
|
|
|
Basalt
Newbie
Joined: 29 Feb 2016 Status: Offline Points: 7 |
Post Options
Thanks(0)
Quote Reply
Posted: 29 Feb 2016 at 10:14pm |
Actually my optical wasn't hooked up yet.
|
|
|
|
|
Basalt
Newbie
Joined: 29 Feb 2016 Status: Offline Points: 7 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 Mar 2016 at 7:10pm |
|
Well, can't change settings in BIos, it locks up before I can save changes. Not locking up any more on the desktop, but my browsers are having troubles getting to different websites, keep having to refresh. Hard to tell if that's my system or just a bad router up line. Looks like I'll have to take this up with ASRock directly since I cannot resolve it.
|
|
|
|
|
GripS
Newbie
Joined: 23 Jan 2016 Status: Offline Points: 21 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 Mar 2016 at 6:36am |
|
Can you navigate the BIOS after clearing the CMOS? How about using the backup BIOS? I have random freezing in the UEFI as well, it seems to be a common issue even when a system is 'stable'. I think if you click around on stuff too quickly it locks it up. Try just using the keyboard to navigate instead of the mouse.
|
|
|
|
|
Basalt
Newbie
Joined: 29 Feb 2016 Status: Offline Points: 7 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 Mar 2016 at 7:19pm |
I thought about the second bios, may try that tonight, work has owned me for the last couple of days. Since I forced the NIC update, anddid some Windows Tweaking, the desktop has been stable. If I use Chrome instead of Edge or Explorer I also don't seem to have Issues with the failure to find the website I direct the browser too. I also downloaded the ASRock desktop software. It allows me to move around in the BIOS from windows without any issues, changing settings at will. I am really thinking the UEFI itself is buggy as you mentioned. Is there a way to step pass the UEFI and go directly to the old school BIOS screen? Oh and an FYI for anybody else trying to kick the kinks out of a new mobo. The ME update at I couldn't get to install from the Ap store? It's older than the one that flashes in with the P1.60 BIOS, hence why it won't update. Anyways, I'll try the second BIOS (Already reset the cmos,) tonight.
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
netjrb wrote: