![]() |
Z170m PRO4S beep codes |
Post Reply ![]() |
Page <12 |
Author | |
Cicca ![]() Newbie ![]() Joined: 26 May 2016 Location: Turin Status: Offline Points: 8 |
![]() ![]() ![]() ![]() ![]() |
Just tried....nothing changes....that was not the problem.....
![]() Other ideas..?! |
|
![]() |
|
parsec ![]() Moderator Group ![]() ![]() Joined: 04 May 2015 Location: USA Status: Offline Points: 4996 |
![]() ![]() ![]() ![]() ![]() |
Have you done a UEFI/BIOS clear yet? You can do that by moving the jumper on the CLR_CMOS header. That header is on the lower edge of the board, on the right side.
Do you know how to do that? Be sure the PC is off, PSU is off and disconnected from AC power. |
|
![]() |
|
Cicca ![]() Newbie ![]() Joined: 26 May 2016 Location: Turin Status: Offline Points: 8 |
![]() ![]() ![]() ![]() ![]() |
Yes, I did it twice....once before removing the video card (since I had moved the DIMMs from a slot to another), and then after.....same threee long beeps immediatly at the power up....
|
|
![]() |
|
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 23963 |
![]() ![]() ![]() ![]() ![]() |
OK, now try removing the RAM from the system entirely and see if you get the same beep code without it. If the code is different then the RAM is not the problem.
|
|
![]() |
|
![]() |
|
Cicca ![]() Newbie ![]() Joined: 26 May 2016 Location: Turin Status: Offline Points: 8 |
![]() ![]() ![]() ![]() ![]() |
Hi....update status: removed both DIMMs (from slots A2/B2), cleared the CMOS, turned on.....same three beeps....
![]() ![]() Now....the new problem is that it doesn't seem to post/boot....I say "seem" because I have no proper cable to connect the monitor (the video card has a Dispay Port output, but the MB no, and the monitor has no HDMI input)....but I hear no "beep" between the POST and the boot (in any case, it can't boot anything since the HD is empty).... Now....what's your suggestion...?! Buy a cable, and see how it goes on....or try to mount the video card back....?! |
|
![]() |
|
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 23963 |
![]() ![]() ![]() ![]() ![]() |
Try mount the video card and see how it goes. Good luck.
|
|
![]() |
|
![]() |
|
Cicca ![]() Newbie ![]() Joined: 26 May 2016 Location: Turin Status: Offline Points: 8 |
![]() ![]() ![]() ![]() ![]() |
YEAH !!! It goes !!! Thanks for all the help !!!
![]() |
|
![]() |
|
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 23963 |
![]() ![]() ![]() ![]() ![]() |
Glad to hear it, awesome job
![]() |
|
![]() |
|
![]() |
Post Reply ![]() |
Page <12 |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |