![]() |
RX 6800 XT no LED |
Post Reply ![]() |
Page <12 |
Author | |
Gastrikhell ![]() Newbie ![]() ![]() Joined: 06 Dec 2019 Status: Offline Points: 30 |
![]() ![]() ![]() ![]() ![]() |
I have no light on my RX 6800 XT Phantom Gaming... The switch is ON but it does not work.
I've tried the firmware update in CMD (administrator) but it fails. I'm running Windows 11. Is it defect? |
|
![]() |
|
ale317 ![]() Newbie ![]() Joined: 27 Nov 2022 Location: £о£и£ Status: Offline Points: 105 |
![]() ![]() ![]() ![]() ![]() |
UPDATE PASS PRONT OK- FAN NO
|
|
![]() |
|
ale317 ![]() Newbie ![]() Joined: 27 Nov 2022 Location: £о£и£ Status: Offline Points: 105 |
![]() ![]() ![]() ![]() ![]() |
Я в?кл??ил блок пи?ани? на но?? и ???ом "Update Pass" ?ол?ко ?або?ае? rgb на пе?едней панели, а вен?ил??о? не? rgb
|
|
![]() |
|
Winterborn107 ![]() Newbie ![]() Joined: 19 Nov 2022 Location: Wisconsink Status: Offline Points: 65 |
![]() ![]() ![]() ![]() ![]() |
also, i see no options in Asrock tweek to turn on RGB. Polychrome sync recognizes the GPUs front side RGB but is unable to control them. dose not recognize the fans or pin header Argb
|
|
![]() |
|
Winterborn107 ![]() Newbie ![]() Joined: 19 Nov 2022 Location: Wisconsink Status: Offline Points: 65 |
![]() ![]() ![]() ![]() ![]() |
The Firmware Update exe. closed quickly after it completed, i think. i never did see an "update pass" msg before the program closed automatically. ASRoock Tweak appears to have full control over my GPU. no problems there, but still no lights on my gpu, even after reboot.
|
|
![]() |
|
ale317 ![]() Newbie ![]() Joined: 27 Nov 2022 Location: £о£и£ Status: Offline Points: 105 |
![]() ![]() ![]() ![]() ![]() |
?д?ав??в?й?е ?и?е? UPDATE FAIL
|
|
![]() |
|
ASRock_TSD ![]() ASRock_Official ![]() Joined: 20 Mar 2015 Status: Offline Points: 8667 |
![]() ![]() ![]() ![]() ![]() |
Dear Winterborn107,
This is ASRock technical support. Thanks for posting your query to the ASRock forum. Regarding your question, kindly refer to the followings: 1. Boot up the system and install the graphics card driver. 2. Download the following tool and unzip it. https://download.asrock.com/TSD/Desktop/Tool/RGB%20FW/RX6800%20PGD%2016GO.zip 3. Run command prompt as Administrator. 4. Go to the directory where the tool is located. e.g. Type cd (Directory of the RX6800 PGD 16GO file) 5. Run the update tool by typing "Update_RX6800_PG.cmd" 6. The update process may take a while. 7. When the message "Update Pass" shows up, it means that the graphics card firmware has been flashed successfully. 8. Please turn on the RGB software and check if the RGB can be controlled properly. https://download.asrock.com/Utility/RGB/PolychromeSYNC(v1.0.26).zip With thanks, ASRock TSD Edited by ASRock_TSD - 07 Dec 2022 at 4:16pm |
|
![]() |
|
Winterborn107 ![]() Newbie ![]() Joined: 19 Nov 2022 Location: Wisconsink Status: Offline Points: 65 |
![]() ![]() ![]() ![]() ![]() |
Motherboard: MSI MPG Z490 GAMING CARBON WIFI LGA 1200 Intel Z490 SATA 6Gb/s ATX Intel Motherboard
|
|
![]() |
|
Winterborn107 ![]() Newbie ![]() Joined: 19 Nov 2022 Location: Wisconsink Status: Offline Points: 65 |
![]() ![]() ![]() ![]() ![]() |
Just got a new Phantom Gaming RX 6800 XT in a new computer, but the led RGB lights do not turn on at all. everything else works, and if i plug a LED strip into the graphics card the strip works fine. tried resetting the card, same problem.
|
|
![]() |
Post Reply ![]() |
Page <12 |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |