ASRock.com Homepage
Forum Home Forum Home > OverClocking(OC) Zone > OC Technical Discussion
  New Posts New Posts RSS Feed - B365M Phantom Gaming 4 OC not available
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

B365M Phantom Gaming 4 OC not available

 Post Reply Post Reply
Author
Message
hoockian View Drop Down
Newbie
Newbie


Joined: 08 Jun 2023
Status: Offline
Points: 35
Post Options Post Options   Thanks (0) Thanks(0)   Quote hoockian Quote  Post ReplyReply Direct Link To This Post Topic: B365M Phantom Gaming 4 OC not available
    Posted: 08 Jun 2023 at 8:05pm
Hello, I have an ASROCK B365M Phantom Gaming 4, BIOS version P4.30, I installed a 2666Ghz DDR4 memory, but from the BIOS it won't let me set the frequency, any solution?, I have looked in google and help but I can't find a solution, according to ASRock this board supports up to 2666Ghz. thank you so much
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Online
Points: 24278
Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 08 Jun 2023 at 10:38pm
Under the "OC Tweaker" tab in your UEFI, DRAM Settings -> Load XMP - Enable.
Back to Top
hoockian View Drop Down
Newbie
Newbie


Joined: 08 Jun 2023
Status: Offline
Points: 35
Post Options Post Options   Thanks (0) Thanks(0)   Quote hoockian Quote  Post ReplyReply Direct Link To This Post Posted: 08 Jun 2023 at 10:49pm
Thanks for helping,

What you tell me about XMP Load in my BIOS P4.30 does not appear, and manually it only leaves me up to 2400, I am desperate since I bought the new T-Forge RAM from Teamgroup and I am not getting any performance out of it.

Greetings
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Online
Points: 24278
Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 10 Jun 2023 at 11:20pm
If the setting is missing then it's likely intel forced ASRock to remove it. Technically
XMP is "overclocking" which intel only allow on their z series chipsets. Motherboard
manufacturers often enable XMP anyway but intel will sometimes get angry and force
them to remove it again.

That said, if your RAM is 2666 you are not missing out on any noticeable performance
if you are running at 2400. In games you will not see more than a single FPS
difference in most titles.

The difference between 2666 and 2400 is actually very small in practical use.

Edited by Xaltar - 10 Jun 2023 at 11:21pm
Back to Top
Alikhan View Drop Down
Newbie
Newbie
Avatar

Joined: 08 Jun 2023
Location: jahlem
Status: Offline
Points: 60
Post Options Post Options   Thanks (0) Thanks(0)   Quote Alikhan Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2023 at 10:57pm
Originally posted by hoockian hoockian wrote:

Hello, I have an ASROCK B365M Phantom Gaming 4, BIOS version P4.30, I installed a 2666Ghz DDR4 memory, but from the BIOS it won't let me set the frequency, any solution?, I have looked in google and help but I can't find a solution, according to ASRock this board supports up to 2666Ghz. thank you so much


"Hi there,

I had a similar issue with my ASRock B365M Phantom Gaming 4 motherboard. Updating the BIOS to the latest version and enabling the XMP/DOCP profile did the trick for me. Make sure to follow the instructions provided by ASRock carefully. If you're still facing difficulties, reaching out to ASRock's technical support could provide further assistance tailored to your specific motherboard model. Good luck!

Best regards,"

Edited by Xaltar - 08 Aug 2023 at 2:50am
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.297 seconds.