![]() |
Single Sided DDR3 RAM Compatibility Issues |
Post Reply ![]() |
Author | |
infernojericho ![]() Newbie ![]() Joined: 08 May 2016 Location: Hong Kong Status: Offline Points: 6 |
![]() ![]() ![]() ![]() ![]() Posted: 08 May 2016 at 7:19pm |
Hi all,
I have an older AMD 880GM-LE FX AM3 motherboard, and I am trying to get it to with with single sided DDR3 2GB RAM modules. The BIOS version is 1.3. The brand of the RAM I have is Silicon Power. Problem is when I insert my 2 sticks of the DDR3 2GB RAM module, the system would only run the 2 x 2GB in single channel mode, and only 2GB would be usable. Is there anything I can do? (Apart from buying double sided RAM...) Thanks!!! |
|
![]() |
|
parsec ![]() Moderator Group ![]() ![]() Joined: 04 May 2015 Location: USA Status: Offline Points: 4996 |
![]() ![]() ![]() ![]() ![]() |
If you check the Memory QVL for the 880GM-LE FX board, you'll find both DS and SS types of memory listed:
http://www.asrock.com/mb/memory/880GM-LE%20FX.pdf So it seems there is another reason why your Silicon Power SS memory does not work well in your board. It could be the memory chips themselves that are not compatible with the memory controller in your CPU. Your CPU is.... ?? Did you clear the BIOS after putting the new memory in your board? Edited by parsec - 08 May 2016 at 7:46pm |
|
![]() |
|
infernojericho ![]() Newbie ![]() Joined: 08 May 2016 Location: Hong Kong Status: Offline Points: 6 |
![]() ![]() ![]() ![]() ![]() |
Thanks for the quick response
I don't have the RAM with me at the moment so I can't tell for sure the model. The CPU is a Phenom 955 Tried clearing the CMOS, no luck Interestingly I could only get the system to power up when I have 2 RAM modules installed. System won't boot if I only insert 1 RAM module. The SP RAM is very very poor in compatibility, I have tried the RAM on at least 10 motherboards (Tried on both Intel and AMD platforms) and it would only fully work on an Asus AM3 motherboard. All the other boards won't power up. And on a separate topic I tried using the Instant Flash to upgrade the BIOS to 1.7, however I have copied the flash file (Yes, I did unzip it) and copied it to the root directory of my C drive and my USB Drive. The Instant Flash utility detects the C drive and flash drive, but was unable to detect the BIOS upgrade file. I tried it with both 1.5 and 1.7, both unsuccessful. Anything I am doing wrong? Thanks |
|
![]() |
|
parsec ![]() Moderator Group ![]() ![]() Joined: 04 May 2015 Location: USA Status: Offline Points: 4996 |
![]() ![]() ![]() ![]() ![]() |
I've never worked with that (early) version of Instant Flash, within an actual BIOS UI! By that I mean a non-UEFI version.
What USB port did you use for the USB flash drive? You should use one on the board's IO panel. Both the USB flash drive and partition on the C drive that can have the BIOS update file on it must be partitioned in FAT32 format. That's why I just use a USB flash drive. If you've formatted your USB flash drive as anything but FAT32, it won't work for Instant Flash. |
|
![]() |
|
infernojericho ![]() Newbie ![]() Joined: 08 May 2016 Location: Hong Kong Status: Offline Points: 6 |
![]() ![]() ![]() ![]() ![]() |
Hi, thanks for the reply
I just checked the model of my Silicon Power RAM module, its SP002GBLTU133V01, DDR3-1333(CL9), single sided Its a different model from the RAM list Thanks for letting me know that a FAT32 formatted drive is needed, will try it again later Do you think upgrading the BIOS will help at all? |
|
![]() |
|
infernojericho ![]() Newbie ![]() Joined: 08 May 2016 Location: Hong Kong Status: Offline Points: 6 |
![]() ![]() ![]() ![]() ![]() |
Just tried to upgrade the BIOS, no luck
I used a Sandisk Cruser 2GB USB Flash, formatted with FAT32, to be safe I copied both the ZIP file (880GM-LE FX(1.70)ROM.zip, and the extracted file, 880GLFX1.70, to the root of the USB Flash Drive And yes, it is inserted to the rear I/O panel USB port The Instant Flash was able to detect the Flash drive, but does not detect the BIOS ROM file. What else am I missing? Cheers |
|
![]() |
|
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 23963 |
![]() ![]() ![]() ![]() ![]() |
Are you sure you have the 880GM-LE FX not the 880GM-LE? The boards look almost identical but use different BIOS. Try grab the latest BIOS for the 880GM-LE (not FX) and see if that works. Don't worry, if it is wrong the instant flash will not detect it as a viable update.
Edited by Xaltar - 09 May 2016 at 6:05pm |
|
![]() |
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |