I have X79 Extreme11 take to long time to run

Author

Message

Topic Search

Topic Options

alazabe

Newbie

Joined: 25 Jun 2016
Location: kuwait city
Status: Offline
Points: 4

Post Options

Post Reply

Quote alazabe

Report Post

Thanks(0)

Quote

Topic: I have X79 Extreme11 take to long time to run
Posted: 25 Jun 2016 at 3:38am

My motherboard debug led is going crazy

it go 60 61 39 then d6

i need help icant even go to the the motherboard UEFI only after a long time like 10 to 20 muintes

PLS help me to fix it soon

Thanks

alazabe

Newbie

Joined: 25 Jun 2016
Location: kuwait city
Status: Offline
Points: 4

Post Options

Post Reply

Quote alazabe

Report Post

Thanks(0)

Quote

Posted: 27 Jun 2016 at 1:29pm

Why there no help ?

here a video of the motherboard debug light

https://www.youtube.com/watch?v=5EoNbD3Pxe0

Pls help asap

vacaloca

Newbie

Joined: 05 May 2016
Status: Offline
Points: 36

Post Options

Post Reply

Quote vacaloca

Report Post

Thanks(0)

Quote

Posted: 28 Jun 2016 at 5:13am

Would be ideal if you post detailed system/component specs... it's hard to debug when no one is aware of what components (RAM, power supply, CPU, etc) you are using on the board.

Without knowing anything else:

0a) Make sure BIOS version on board supports the CPU you have installed.

1) Make sure CPU is seated correctly on slot

2) Make sure RAM is seated correctly -- try using only 1 DIMM and/or using a different memory DIMM

3) Make sure video card is seated correctly -- try changing video cards if possible

Edited by vacaloca - 28 Jun 2016 at 5:16am

Xaltar

Moderator Group

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 24653

Post Options

Post Reply

Quote Xaltar

Report Post

Thanks(0)

Quote

Posted: 28 Jun 2016 at 5:23am

Clear CMOS using this method then post back your results.

Also please provide system specs and answer the following:

Age of PC?

Is this a new problem?

Did the PC work normally before?

parsec

Moderator Group

Joined: 04 May 2015
Location: USA
Status: Offline
Points: 4996

Post Options

Post Reply

Quote parsec

Report Post

Thanks(0)

Quote

Posted: 28 Jun 2016 at 12:09pm

alazabe wrote:

Hi

My motherboard debug led is going crazy

it go 60 61 39 then d6

i need help icant even go to the the motherboard UEFI only after a long time like 10 to 20 muintes

PLS help me to fix it soon

Thanks

No, the Dr Debug LED display is not going crazy when it shows those numbers, which are called POST codes.

It is normal for the codes to be displayed on the display. If the PC completes POST, the codes disappear. If one code stays on the display, and does not change or turn off, that code tells you in general what is wrong. Since there was a problem with some part of your hardware, the PC could not start or boot, and the startup process was stopped. This can happen to any PC.

So the last code you get is d6, is that right?

If you look at your board's information page, the FAQ section has information about the Dr Debug codes. You can find that here:

http://www.asrock.com/mb/Intel/X79%20Extreme11/?cat=FAQ

We can see that a d6 code is a problem with the video card:

The VGA could not be recognized. Please clear CMOS and try re-installing the VGA card. If the problem still exists, please try installing the VGA card in other slots or use other VGA cards.

What video card are you using, and which slot is it in?