![]() |
Z170 extreme4 dr.debug 04 |
Post Reply ![]() |
Page <1234> |
Author | |
HappyMan ![]() Newbie ![]() Joined: 09 Aug 2016 Status: Offline Points: 19 |
![]() ![]() ![]() ![]() ![]() |
But CPU pass 2hour prime95 4.5Ghz on 1.27v (if i luck to run without freezes 04). And can freeze with 04 code only at start. And i must set 1.36 just for no freezes PC start. Maby exist a way to increase the voltage only on startup.
wardog, 19.15.15.36 (rc1) timings don't give resulth ( |
|
![]() |
|
parsec ![]() Moderator Group ![]() ![]() Joined: 04 May 2015 Location: USA Status: Offline Points: 4996 |
![]() ![]() ![]() ![]() ![]() |
As Xaltar said, the only time the Dr Debug/POST codes indicate a problem is when the PC is starting, and the PC does not boot/start Windows or whatever your OS is. The POST codes are displayed on the Dr Debug display as each POST process is run during the entire POST procedure. That is normal. If a POST process fails for some reason, then POST stops, the code of the POST process that failed is displayed, and the OS boot process stops. If you see a code on the Dr Debug display when the PC is being shutdown, it does not mean anything at all. The POST procedure does not run when a PC is being shutdown, any code displayed at that time does not mean anything. If your PC boots your OS fine, you do not have any problem with your memory as far as the POST tests can find. The memory controller is part of your Skylake CPU. If an over clock fails because of too little voltage, any number of things can go wrong in the CPU, including a memory problem. |
|
![]() |
|
HappyMan ![]() Newbie ![]() Joined: 09 Aug 2016 Status: Offline Points: 19 |
![]() ![]() ![]() ![]() ![]() |
Cool. I can try change timing only In 2-3 hours. I can write process on video (if it helps).
|
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
I'm Baaaack. And up. For a little while anyways. T'was a long night here staring at the heavens.
|
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
Whoa there. Looks like the BIOS is miscalculating these sticks main 4 timings and maybe CR(Command Rate).
Are you knowledgeable enough to change the timing manually in the BIOS? If so, let's attempt a mediocre timing by what tCL - 19 tRCP - 15 tRP - 15 tRAS - 36 CR - 1 (and if there's issues, change CR to 2 and retry) DRAM Voltage - 1.20 (and if there's issues, add +0.05v making +1.25 and retry. Fail at +1.25v? Bump another +0.05v making +1.30 and retry.) I'll be back here in 4-6hrs to look for any reply's/results. In a few minutes me and my Wife are driving out into the desert far away from light pollution to view/photograph the Perseid meteor shower. Edited by wardog - 12 Aug 2016 at 2:10pm |
|
![]() |
|
HappyMan ![]() Newbie ![]() Joined: 09 Aug 2016 Status: Offline Points: 19 |
![]() ![]() ![]() ![]() ![]() |
No problem at all for me . Thank you for helping
http://imgur.com/a/NLeET http://imgur.com/a/wJfCP |
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
No, don't downgrade. The last three BIOSes have had memory compatibility improvements.
Will you download and install CPU-z, start 4 instances of it to show me the SPD and Memory tab of each of the two sticks please. And I should say thank you for you patience too. It's not easy diagnosing over hours between forum posts. |
|
![]() |
|
HappyMan ![]() Newbie ![]() Joined: 09 Aug 2016 Status: Offline Points: 19 |
![]() ![]() ![]() ![]() ![]() |
Yes I have 3.40 bios version on first chip and 3.20 on second. I
Asked about downgrade (if this possible) to which version? |
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
HERE you said you've already flashed the running A BIOS 3.40. If you did not, then yes. Use the Instant Flash method from within your BIOS in the Tools tab. Do not use the Internet Flash method as it is, IMHO, unreliable and will more easily corrupt your BIOS, rendering your board unusable. If you need instruction for using Instant Flash post back and I'll walk you through it. |
|
![]() |
|
HappyMan ![]() Newbie ![]() Joined: 09 Aug 2016 Status: Offline Points: 19 |
![]() ![]() ![]() ![]() ![]() |
sry. i have p2.10 numbers on both stickers.
maby i must try to flash another BIOS(more compatible with my RAM) ? Edited by HappyMan - 12 Aug 2016 at 2:30am |
|
![]() |
Post Reply ![]() |
Page <1234> |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |