Z170MPro - No Beep, No Screen, Just Fans,Reboot 3s |
Post Reply | Page <12 |
Author | |
GreatFullTekeek
Newbie Joined: 12 Jan 2017 Status: Offline Points: 14 |
Post Options
Thanks(0)
|
it is NOT WORKING!
ok I got now the G.Skill F4-3000C15D-16GTZ which is listed on the Asrock compatibility page. I plugged in one of the two supported rams in A1 or B1, it dont matter where, and how often i Clear the CMOS also dont make any difference - same problem as described in my first post so these Supported RAMS dont work - or is it a other Problem? I have a project which i should deliever... |
|
GreatFullTekeek
Newbie Joined: 12 Jan 2017 Status: Offline Points: 14 |
Post Options
Thanks(0)
|
Z170MPro Impressions
a few pictures about the setup |
|
parsec
Moderator Group Joined: 04 May 2015 Location: USA Status: Offline Points: 4996 |
Post Options
Thanks(0)
|
Most of the DDR4 memory whose speed is above 2400 will be 1.35V. All DDR4 memory above 2666 will be 1.35V, that is normal. The Viper memory you have now is 1.35V, and the timings are 16 16 16 36. Click on Additional Information on the page below: https://patriotmemory.com/product/viper-4-series-ddr4-16gb-2-x-8gb-3000mhz-kit/ All DDR4 memory will work at first at its default speed, which is 2133 or 2400, at 1.2V. 1.35V is only needed when the memory is set to 3000. Memory voltage is not the problem. You cannot compare the timings of DDR4 memory to the timings of DDR3. You will never find DDR4 memory less than 12 - 14, and that will be at 2133. The faster the DDR4 memory speed is, the higher the timings will be. The price of DDR4 memory has gone up over the last few months, now is not a good time to find good prices. |
|
GreatFullTekeek
Newbie Joined: 12 Jan 2017 Status: Offline Points: 14 |
Post Options
Thanks(0)
|
ok thx for the good explanation.
so the voltage is maybe not the problem here. And it was nonsense to get other RAMs. but how can i now find out what the problem is now? i have no debugging via PC-Speaker, or blinking LEDs. I cant return all the stuff, and say the CPU is maybe dead, and the Motherboard is maybe dead, or the PS is maybe dead, and after a week or more i have the money back, and then have to wait a few days longer to get a new board and cpu... when not using "shared memory" for internal (CPU?)graphics, it reboots endless, and when i stuff a graphic card into PCIe, the Display connected to the card dont regocnize the card (no signal going to sleep), and the PC seems to run (PS+CPU Fans are running endless static in speed)... that should be enouh info to localize the probelm. |
|
GreatFullTekeek
Newbie Joined: 12 Jan 2017 Status: Offline Points: 14 |
Post Options
Thanks(0)
|
i tried now the cheapest, slowest, and smalest RAM i Found in the Compatibility list:
Kingston KVR21N15S8/4 That DONT solve the Problem, it just avoid the endless Boot Tryings: Start the PC, now all FANS are running on Static Speed (same behavior like bevore when i plugged in a PCIe Card) No Display-Data Output on HDMI or DVI (no PCIe Card is connected) |
|
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Online Points: 22838 |
Post Options
Thanks(0)
|
|
|
GreatFullTekeek
Newbie Joined: 12 Jan 2017 Status: Offline Points: 14 |
Post Options
Thanks(0)
|
yes i did
i cleared every time before i tried all 4 SLOTs |
|
GreatFullTekeek
Newbie Joined: 12 Jan 2017 Status: Offline Points: 14 |
Post Options
Thanks(0)
|
i dont get the money back from my dealer! because it had taken to long since i buyed it, i only could let "repair" the board.
i only hear the memory the memory, clear c-mos... i dont feel i got helped here. i think i have all rights to be pissed > it would be so easy >>> DEBUG >>> but no beep no blink code? ASROCK in which way should a end-user debug a problem? Say it! >Should he run to a Expert, which is only a "expert" because he has spare parts to replace the whole setup to see what the problem is? I cant believe it. What is about End-user - is he a stupid sheep in your eyes? >Or - it seems to better that the people ask the forum, and some users look into the magical ball and see "it could be the memory"... and when it wasnt the memory > then the magical ball dont see anything @ all. i whish i had known this before! because i cant get rid of it now, i dont know -should i sell it as "faulty" or "working". And if i sent it back to Asrock, and they say the board is ok > who helps me then? i had to buy a new psu, a new ram (as i did already twice!!!) and a new CPU > Really i dont have the money for twice the setup, or for a "expert" who has Edited by GreatFullTekeek - 25 Jan 2017 at 9:55am |
|
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Online Points: 22838 |
Post Options
Thanks(0)
|
I am sorry to hear about your difficulties. Please bare in mind that ASRock is not responsible for the policies of retailers regarding returns. Also important to note is the fact that while this is the tech support section of the forums, it is not ASRock's official tech support. Assistance is rendered here by other forum members not directly by ASRock. On occasion an ASRock Tech Support representative will post here with important updates and fixes but this is not common place. Even the moderators here are simply forum members such as yourself and do not speak for or represent ASRock here on the forums. ASRock representatives here have the name ASRock in their name in the following format:
ASRock_Official ASRock_TSD ASRock_News Again, I feel for you, we all know how frustrating it is when new parts do not work right. Good luck with system, please post back here once you get your board back. If you need assistance from ASRock Tech support you can contact them here: ASRock Taiwan (global support): ASRock USA: Support Phone: 1-909-590-8308 Support Email: support@asrockamerica.comGood luck
|
|
|
|
GreatFullTekeek
Newbie Joined: 12 Jan 2017 Status: Offline Points: 14 |
Post Options
Thanks(0)
|
today i got my money back, i will try my luck with a asus z170M-Plus.
topic can be closed |
|
Post Reply | Page <12 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |