7700k & Z270 Extreme4 - Can't get 5Ghz Stable :/ |
Post Reply | Page <123> |
Author | |
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
|
Thanks for the info
These boards are still very new and so far a lot better than the 100 series boards were on release, still, there will be some bugs to work out.
|
|
|
|
Nyrdian
Newbie Joined: 17 Feb 2017 Status: Offline Points: 1 |
Post Options
Thanks(0)
|
morbid_bean
Newbie Joined: 26 Feb 2017 Status: Offline Points: 5 |
Post Options
Thanks(0)
|
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
|
All I know is that 1 is the highest value and 4 is the lowest. Auto seems to do exactly what it says, dynamically adjust between 1 - 4 or off. I played around with this a lot on my Z270 Gaming K6 when I was pushing my overclocks and found the best results on auto. I achieved 5.1ghz @1.44v with water cooling and 5.0 at 1.38v on air.
I now use the system @stock with MCE enabled which puts me at 4.2ghz and it is more than adequate for my every day tasks/gaming. If I had a decent GPU then it would be worth pushing it to 4.8 or even 5.0 but my GTX 960 bottlenecks long before the 7600k in my system. So far as I could figure out, auto is the closest thing to off you will find.
|
|
|
|
MaloW
Newbie Joined: 21 Mar 2017 Status: Offline Points: 1 |
Post Options
Thanks(0)
|
I am too noticing instability with LCC on my Z270 Extreme4.
With LLC level 4 (lowest) my 7700K is stable at 5.0Ghz through hours of RealBench at offset voltage +235mv, which results in a voltage between 1.312-1.328V during RealBench. However when doing light browsing and stuff I'm getting spikes up to 1.440V, so I would like to use LLC to get those down a bit. However with LLC level 3, and the offset voltage set to +175mv, the spikes are down to 1.392V, and I get 1.328-1.344V during RealBench, which is quite a bit higher voltage than with LLC4, but it results in blue screens after just seconds or minutes of RealBench. Does anyone have any tips on how to fix this? Or is it an issue with the actual board that can't be fixed? |
|
MASTRandDSASTR
Newbie Joined: 21 May 2017 Location: South Carolina Status: Offline Points: 6 |
Post Options
Thanks(0)
|
I was reading this to see I found anyone that has OC their 7700k over the 5Ghz mark. It seems 5Ghz is a kind of threshold for most. Im not an expert, but I do have some experience OC, and I was running @5.2Ghz-1.395v when I found this. Using the same MoBo in question (z270 Extreme4). The preset OCs are nifty, but it seems it's more for noobs than anything. Needless to say I tried those too. Not bad, but the performance gain did not justify the temperature raise. I was looking at 80c-90c+ depending on settings attempted. This was before I decided to delid (using Cool laboratories liquid metal) and add an AIO cooler. Works great. i have now been able to reach 5.3Ghz-1.47v. Looks stable to me. More testing needs to be done. My question for anyone working with similar CPU and MoBo is: Have you gotten higher clocks?, and if so; please let me know what speed you tried, and at what voltage. I've even tried with the PLL and VCCIO, but I don't think I'm that experienced yet. Message me please or just reply to my post. Id like to see what other people are working with. Personally I don't see how 5Ghz is super impressive in the Kaby Lake. I was expecting more.
|
|
M&D
|
|
MASTRandDSASTR
Newbie Joined: 21 May 2017 Location: South Carolina Status: Offline Points: 6 |
Post Options
Thanks(0)
|
I neglected to mention that after the cooling solutions I was looking at 72C max temp in full load even during a 25min stress test with the 5.2Ghz setting. 74C now with 5.3Ghz. The delid with liquid metal will give you a 10C minimum decrease in temp. I've read you can get -25C, but I don't know how true that is since I've actually done it. If your ambient temp is cooler then you can obviously see better temps.
|
|
M&D
|
|
MASTRandDSASTR
Newbie Joined: 21 May 2017 Location: South Carolina Status: Offline Points: 6 |
Post Options
Thanks(0)
|
M&D
|
|
parsec
Moderator Group Joined: 04 May 2015 Location: USA Status: Offline Points: 4996 |
Post Options
Thanks(0)
|
So you don't see any voltage spikes during RealBench? What are you using to monitor VCore, CPU-Z? Reaching 5GHz with a VCore of under 1.4V will be very difficult, and require a very good CPU, the luck of the draw of course. Are you using the lower LLC values for some reason, with an OC to 5GHz? I know you like to see the lower VCore, who doesn't, but the required VCore above ~4.8GHz is not linear, it needs much more and a tighter LLC is needed. |
|
MASTRandDSASTR
Newbie Joined: 21 May 2017 Location: South Carolina Status: Offline Points: 6 |
Post Options
Thanks(0)
|
Like I said. Level 1. You might be able to get away with 2
|
|
M&D
|
|
Post Reply | Page <123> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |