H110 Pro BTC not showing display

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   I have a problem with my H110 Pro BTC motherboard, 
I had 6 RX570 cards on the motherboard running fine.
I powered down the motherboard (PSUs still turned on) to swap risers in 2 slots.  While I doing the riser swap the motherbord and CPU powered back on!!  Since this happened I no longer get any video display from the motherboard DVI port or from a video card in the PCI16 slot.

No display whatsoever... no beeps, all that happens is CPU fan runs when I power on the motherboard.

What to do?

Please help

Edited by Xaltar - 17 Nov 2017 at 7:17pm

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
rgoulter Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 17 Nov 2017 Status: Offline Points: 4	Post Options Post Reply Quote rgoulter Report Post Thanks(0) Quote Reply Topic: H110 Pro BTC not showing display Posted: 17 Nov 2017 at 4:38pm
	I have a problem with my H110 Pro BTC motherboard, I had 6 RX570 cards on the motherboard running fine. I powered down the motherboard (PSUs still turned on) to swap risers in 2 slots. While I doing the riser swap the motherbord and CPU powered back on!! Since this happened I no longer get any video display from the motherboard DVI port or from a video card in the PCI16 slot. No display whatsoever... no beeps, all that happens is CPU fan runs when I power on the motherboard. What to do? Please help Edited by Xaltar - 17 Nov 2017 at 7:17pm

Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 27398	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Posted: 17 Nov 2017 at 7:20pm
	Pull the system apart then clear CMOS using this method: http://forum.asrock.com/forum_posts.asp?TID=630&title=how-to-clear-cmos-via-battery-removal Then reinstall only the CPU, 1 stick of RAM and PSU and see if you can post. If not, it is very likely the board is damaged. I edited your post, we are here to help so there was no need


Moinerus Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 17 Nov 2017 Status: Offline Points: 1	Post Options Post Reply Quote Moinerus Report Post Thanks(0) Quote Reply Posted: 17 Nov 2017 at 7:54pm
	I also have this issue, bare bones with only RAM, CPU and PSU no video (same story with a GPU in the 16x slot). If i pull the ram and I get the appropriate beep codes... Tried the CMOS reset you linked and it makes no difference. Guse this one is an RMA! Edited by Moinerus - 17 Nov 2017 at 7:56pm

rgoulter Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 17 Nov 2017 Status: Offline Points: 4	Post Options Post Reply Quote rgoulter Report Post Thanks(0) Quote Reply Posted: 18 Nov 2017 at 4:56am
	I have cleared the CMOS and still no signal. The board is currently stripped down to just CPU. When I remove the CPU and reinstall the CPU still no signal, same for Ram and CPU. I think it may be terminal unless there is something else to try? anyone? Edited by rgoulter - 18 Nov 2017 at 6:47am

Goldenwave Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 01 Jan 2018 Status: Offline Points: 2	Post Options Post Reply Quote Goldenwave Report Post Thanks(0) Quote Reply Posted: 01 Jan 2018 at 1:37am
	I'm having same issue with little to no response from corporate. I needed to change out the monitor, shut down and when I rebooted... nothing Won't work on any port DVI, onboard, PCI, etc. Has this issue been fixed for anybody. I see lots of people complaining. Yes it makes sense to clear CMOS, but to strip everything off and on, doesn't matter.

broix Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 04 Jan 2018 Status: Offline Points: 4	Post Options Post Reply Quote broix Report Post Thanks(0) Quote Reply Posted: 04 Jan 2018 at 4:43am
	I am having same issue. No display. I have only CPU and 1 stick of DDR4 8GB connected. I had display for a few reboots, but now it is gone. Do we have any other support options?

Goldenwave Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 01 Jan 2018 Status: Offline Points: 2	Post Options Post Reply Quote Goldenwave Report Post Thanks(0) Quote Reply Posted: 05 Jan 2018 at 2:31am
	I think our only options are to return the motherboards. This is rediculous.

puntar Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 17 Jan 2018 Status: Offline Points: 1	Post Options Post Reply Quote puntar Report Post Thanks(0) Quote Reply Posted: 17 Jan 2018 at 3:37am
	Hi, i registred jut fot this reply. Had the same problem.. found out, that the problem was with the power cable; CPU needs to have 8 pin cable connected from PSU to ATX12V1 connector (CPU is actually printed on the cable). Plugged it in, restarted and now everythig works ok. Hope this helps. B.

GrandSab Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 19 Jan 2018 Status: Offline Points: 1	Post Options Post Reply Quote GrandSab Report Post Thanks(0) Quote Reply Posted: 19 Jan 2018 at 5:16am
	I have 2 MOBO's with the same problem. No boot no power up. Only CPU and cooler installed. Replaced trying everything assembly and dissassembly. Connect and Reconnect PSU. No blinking LAN, Cleared CMOS. What is the problem?

bhikku79 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 24 Jan 2018 Location: Pennsylvania Status: Offline Points: 1	Post Options Post Reply Quote bhikku79 Report Post Thanks(0) Quote Reply Posted: 24 Jan 2018 at 10:20am
	I have the same issue, new mobo, installed every thing , worked fine the first day, on second day when I tried to start, CPU Fan runs, LAN light blinks , but no DVI display what so ever, Did CMOS reset , but no change , Dont know what to do . any solution ?