x399 fat1lty Professional Gaming Problems

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   [URL=][/URL]You folks are great!  Thanks much for your replies.

However, even when I set xmp speed to 1866, uefi still shows 2133??

Could you advise on what SoC / Ram voltages to try?

Also, do you know of any memory remapping uefi settings to try?

Edited by jbmerrill - 08 Jan 2018 at 5:51am

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
jbmerrill Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 02 Jan 2018 Location: California Status: Offline Points: 103	Post Options Post Reply Quote jbmerrill Report Post Thanks(0) Quote Reply Topic: x399 fat1lty Professional Gaming Problems Posted: 08 Jan 2018 at 5:50am
	[URL=][/URL]You folks are great! Thanks much for your replies. However, even when I set xmp speed to 1866, uefi still shows 2133?? Could you advise on what SoC / Ram voltages to try? Also, do you know of any memory remapping uefi settings to try? Edited by jbmerrill - 08 Jan 2018 at 5:51am
	X399 Pro Gaming, 2990wx Threadripper,128GB G.Skill RGB 3200,EVGA 1200 P2,EVGA GTX 1080 Ti x 2 SLI, Enermax Liqtech 360mm,Samsung 970 EVO/960 Pro/850 EVOs, Toshiba x300 HDDs, Thermaltake Chaser MK-1

ssateneth Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 19 Oct 2017 Status: Offline Points: 129	Post Options Post Reply Quote ssateneth Report Post Thanks(0) Quote Reply Posted: 08 Jan 2018 at 5:05am
	I cannot find the official AMD source at this time, though here is a copy from a review website. https://techreport.com/review/32474/the-tech-report-system-guide-september-2017-edition/4 "Ryzen Threadripper CPUs are subject to similar limitations, just with four memory channels instead of two: Quad-channel, dual-rank, two DIMMs per channel: DDR4-1866 Quad-channel, single-rank, two DIMMs per channel: DDR4-2133 Quad-channel, dual-rank, one DIMM per channel: DDR4-2400 Quad-channel, single-rank, one DIMM per channel: DDR4-2667 " If you were using single rank ram, then sure, 2133. But you are using dual rank, so 1866. BTW, your hardware reserved thing from OP is a RAM training issue. CPU dropping channels because of bad stability. Adjust stability related stuff (SoC volts, ram volt, etc) until success. Edited by ssateneth - 08 Jan 2018 at 5:20am
	MB: X399 Taichi, UEFI L3.32 VGA: EVGA 1080 Ti FTW3 PSU: Seasonic PRIME 1300 W PLATINUM CPU: AMD Ryzen Threadripper 2950X MEM: 4x16GB, 3600MHz G.Skill Trident Z F4-3600C17Q-64GTZKW

zlobster Members Profile Send Private Message Find Members Posts Add to Buddy List Groupie Joined: 02 Sep 2017 Status: Offline Points: 403	Post Options Post Reply Quote zlobster Report Post Thanks(0) Quote Reply Posted: 08 Jan 2018 at 3:43am
	At that point I'm rather lost! Your mobo & CPU should handle ALL your RAM in quad-channel configuration @ JEDEC speeds. Slow, but it should work. If I were you I'd definitely go with the latest UEFI and try booting up gradually with more and more RAM, i.e. 1 stick, 2 sticks, 3 sticks, etc. Please pay huge attention to the respective RAM slots on the mobo, as you're adding the RAM sticks. At the end you SHOULD see 128GB in quad-channel, being it @ 1866 or 2133MHz. If this doesn't happen I'd start RMA-ing stuff, starting with the mobo, then RAM, then CPU. System not being able to work with default settings in default configuration is called a defect in my book. Lyrical detour - what you're experiencing is one of the reasons I didn't go for Threadripper in first place. TR platform is still in its infancy, plus defects happen and will happen, being on Intel or AMD platforms.
	1700X ZP-B1 (stock); X370 Taichi (UEFI 3.10); 16GB F4-3200C14-8GFX XMP; 256GB 960 EVO; RX 580 NITRO+ 8GB

jbmerrill Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 02 Jan 2018 Location: California Status: Offline Points: 103	Post Options Post Reply Quote jbmerrill Report Post Thanks(0) Quote Reply Posted: 08 Jan 2018 at 2:01am
	Hi, I have tried all uefi versions including betas and nothing will post except for p1.30 (with 2.0 I?�m getting code ?�c0??, and all except for p1.30 are in a boot loop. At this point, I?�m not worried about the speed, but the fact that an O.S. can?�t use more than 32GB, with 96gb ?�hardware reserved?? I am getting quad channel with 128gb with p1.30 and 2133mhz. I do comprehend what people are saying here, but the only thing I have not tried is each individual stick of ram in each slot. P1.30 shows all 128gb in uefi. I have not been able to update uefi with 128gb, (even with clearing cmos) but only max of 64gb in dual channel when updated. I apologize if I am not providing correct info, but please let me know what details I should be supplying. The ram sticks are all serialized in perfect order, so they should be matched as the kit cost me a premium. Thanks very much for your reply. Bryan
	X399 Pro Gaming, 2990wx Threadripper,128GB G.Skill RGB 3200,EVGA 1200 P2,EVGA GTX 1080 Ti x 2 SLI, Enermax Liqtech 360mm,Samsung 970 EVO/960 Pro/850 EVOs, Toshiba x300 HDDs, Thermaltake Chaser MK-1

zlobster Members Profile Send Private Message Find Members Posts Add to Buddy List Groupie Joined: 02 Sep 2017 Status: Offline Points: 403	Post Options Post Reply Quote zlobster Report Post Thanks(0) Quote Reply Posted: 08 Jan 2018 at 12:26am
	Bryan, you're currently wanting to have your cake and eating it too. 1. You're not on the latest UEFI; 2. There is even some more recent beta UEFI; 3. I'd honestly stop any further troubleshooting at this point; 4. Until AMD fix their AGESA nobody is getting good speeds on 128GB; 5. XMP speeds are NOT guaranteed! Not for Intel, not for AMD! End of story! 6. You SHOULD be getting QUAD channel, albeit at lower speeds; If you can't comprehend what people here are saying, I'm afraid you're in for some bad times. Things to try - update that fvcking UEFI for starters, clear the CMOS! Try every possible combination and permutation with your RAM sticks and slots. Make sure RAM sticks are seated properly. Clear CMOS every time you change RAM sticks/slots. There is a chance your RAM sticks are not matched. Happens more often that anyone thinks. Stay positive! Keep us posted!
	1700X ZP-B1 (stock); X370 Taichi (UEFI 3.10); 16GB F4-3200C14-8GFX XMP; 256GB 960 EVO; RX 580 NITRO+ 8GB

jbmerrill Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 02 Jan 2018 Location: California Status: Offline Points: 103	Post Options Post Reply Quote jbmerrill Report Post Thanks(0) Quote Reply Posted: 08 Jan 2018 at 12:06am
	Hello, I'm still using the p1.30 uefi bios and my ram is at 2133mhz even though it is rated 3200mhz, and the most important problem is that the O.S. is only able to use 1/4 of that or 32GB (not 128GB). I can't even remember what combinations I tried with less RAM, but think that the best I got was 4 dimms (64GB) in slots a1,a2,b1,b2, dual channel. I really don't want to try testing each individual slot and each stick of ram, but do you think that would really be the best thing to do, or is this just a configuration that is not possible, even though the specs say it should be? I have tried so many things, that I am at a loss as to know how to proceed. If someone knows what they would do in this situation, I would greatly appreciate any advice. Thanks, Bryan
	X399 Pro Gaming, 2990wx Threadripper,128GB G.Skill RGB 3200,EVGA 1200 P2,EVGA GTX 1080 Ti x 2 SLI, Enermax Liqtech 360mm,Samsung 970 EVO/960 Pro/850 EVOs, Toshiba x300 HDDs, Thermaltake Chaser MK-1

MisterJ Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 19 Apr 2017 Status: Offline Points: 1097	Post Options Post Reply Quote MisterJ Report Post Thanks(0) Quote Reply Posted: 06 Jan 2018 at 8:55am
	ssateneth, where did you get this information? My personal communication with AMD Support says 2133 MHz for 128 GB in TR. Several users have also reported this speed here. Enjoy, John.
	Fat1 X399 Pro Gaming, TR 1950X, RAID0 3xSamsung SSD 960 EVO, G.SKILL FlareX F4-3200C14Q-32GFX, Win 10 x64 Pro, Enermx Platimax 850, Enermx Liqtech TR4 CPU Cooler, Radeon RX580, BIOS 2.00, 2xHDDs WD

ssateneth Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 19 Oct 2017 Status: Offline Points: 129	Post Options Post Reply Quote ssateneth Report Post Thanks(0) Quote Reply Posted: 06 Jan 2018 at 7:58am
	6 beeps is just a false positive and has no bad effects. it is glitch with agesa 1.0.0.4 (threadripper). UEFI 1.80 and later use new agesa and have beep glitch. There are reports that 1.92 beta fixes the beep glitch. @OP, you do realize that the official highest speed supported with your setup (2 dimms per channel, dual rank) is 1866MHz, right? anything higher is overclocking and not guaranteed. I bet if you test your RAM 1 stick at a time, you'll be able to get the rated speed (which is still technically overclocking). You're already getting 2133MHz with 2DPC dual rank, which is better than officially supported speed. Nothing is wrong with your hardware. You're just expecting it to run faster than what it's designed for. You might be better off visiting forums better suited for overclocking if you want to get closer to your RAM's XMP speed.
	MB: X399 Taichi, UEFI L3.32 VGA: EVGA 1080 Ti FTW3 PSU: Seasonic PRIME 1300 W PLATINUM CPU: AMD Ryzen Threadripper 2950X MEM: 4x16GB, 3600MHz G.Skill Trident Z F4-3600C17Q-64GTZKW

lowdog Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 16 Apr 2017 Location: Australia Status: Offline Points: 194	Post Options Post Reply Quote lowdog Report Post Thanks(0) Quote Reply Posted: 06 Jan 2018 at 6:32am
	I get the 6 beeps when I set XMP profile, it's 1000% HCI Memtest stable with XMP @ 2933MHz so who knows what the beeps mean?????????????? Others also get the 6 beeps when they set XMP as well so Asrock need to sort that one out I guess. even though in the link to beep codes 6 beeps is supposed to indicate a keyboard issue I can't seem to accept that one because it just doesn't compute.
	X399 Fat Pro Gaming bios 3.10 - TR4 1900X - 64GB G-SKILL TridentZ F4-3200C14Q-64GTZ @ 3133MHz - Vega 64 AIO with EK block - WC Custom loop - 1500W Silverstone PSU - yay

jbmerrill Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 02 Jan 2018 Location: California Status: Offline Points: 103	Post Options Post Reply Quote jbmerrill Report Post Thanks(0) Quote Reply Posted: 06 Jan 2018 at 1:42am
	Here is an attempt to upload cpu-z image of my memory. Can't tell if it works though. https://imgur.com/a/Np5vI https://www.newegg.com/Product/Product.aspx?Item=N82E16820232562 Edited by jbmerrill - 06 Jan 2018 at 2:36am
	X399 Pro Gaming, 2990wx Threadripper,128GB G.Skill RGB 3200,EVGA 1200 P2,EVGA GTX 1080 Ti x 2 SLI, Enermax Liqtech 360mm,Samsung 970 EVO/960 Pro/850 EVOs, Toshiba x300 HDDs, Thermaltake Chaser MK-1