ASRock.com Homepage
Forum Home Forum Home > Technical Support > Intel Motherboards
  New Posts New Posts RSS Feed - EK-Supremacy MX CPU Waterblock doesn't fit X99M
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

EK-Supremacy MX CPU Waterblock doesn't fit X99M
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
thegreywizard View Drop Down
Newbie
Newbie


Joined: 07 Feb 2016
Status: Offline
Points: 77 		Post Options Post Options   Thanks (0) Thanks(0)   Quote thegreywizard Quote  Post ReplyReply Direct Link To This Post Topic: EK-Supremacy MX CPU Waterblock doesn't fit X99M
    Posted: 12 Jun 2018 at 8:39am
I have an Extreme X99M & absolutely love it

But I was trying to install this custom Matrix waterblock:


And the feet don't seem to fit properly.

From the directions this waterblock should screw right in, but the screws have 2 levels of threads, one thinner than the 2nd tier - but the 1st tier seems like it is supposed to recess into the board so the 2nd tier & fatter threads can screw directly into the board

But the problem is there are no holes for the 1st tier to screw or slide into - there is motherboard where these holes should be

So what can be done?  I don't think it's a good idea to drill out the mobo so these can thread into it, instead I'm thinking of just clipping this thinner 1st tier off so the 2nd tier that's thicker can thread directly into it.

I should also note there is currently a 1/4" gap between the CPU & the bottom of the waterblock with this problem - clipping off the 1st tier would solve this problem it seems.

But I wanted to check here first before I did any modifications.




This backer piece comes with the kit, but according to the directions it should not be needed for the 2011-3:


Back of board showing it's not a good idea to drill out those holes




Edited by thegreywizard - 12 Jun 2018 at 11:54am
Back to Top
badbri View Drop Down
Groupie
Groupie


Joined: 20 Feb 2018
Location: USA
Status: Offline
Points: 415 		Post Options Post Options   Thanks (0) Thanks(0)   Quote badbri Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jun 2018 at 10:46am
Looks like they should have included a second set of differant mount screws for boards that already have back plates. I think your idea of cutting the the fine threads off is a good one but will void the warranty on that water block and if threads are different may not screw in properly. Have you checked the threads on the original cooler and see if they match the 2nd tier fatter threads ?
Do not drill the mount holes out !
https://www.passmark.com/baselines/V9/display.php?id=99573335296
Back to Top
thegreywizard View Drop Down
Newbie
Newbie


Joined: 07 Feb 2016
Status: Offline
Points: 77 		Post Options Post Options   Thanks (0) Thanks(0)   Quote thegreywizard Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jun 2018 at 11:54am
The air cooler I was using came with it's own mounting hardware and won't work for this application.

I am going to call performance-pcs tomorrow and talk to their tech department to see what they suggest.

But you bring up some good points, I'm not so much worried about the warranty on the water block, but my CPU not being cooled properly if it doesn't seat right.
Back to Top
thegreywizard View Drop Down
Newbie
Newbie


Joined: 07 Feb 2016
Status: Offline
Points: 77 		Post Options Post Options   Thanks (0) Thanks(0)   Quote thegreywizard Quote  Post ReplyReply Direct Link To This Post Posted: 15 Jun 2018 at 2:31am
It's been suggested to try and knock out the mobo material that is blocking the hole.

What are the chances that these holes are actually semi-cut and just "stuck"?

I don't want to try and knock them out thinking they're pre-cut in some way and crack the mobo


Edited by thegreywizard - 15 Jun 2018 at 2:32am
Back to Top
wannagofast View Drop Down
Newbie
Newbie


Joined: 05 Aug 2016
Status: Offline
Points: 21 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wannagofast Quote  Post ReplyReply Direct Link To This Post Posted: 15 Jun 2018 at 4:57am
Originally posted by thegreywizard thegreywizard wrote:

[URL=][/URL]
It's been suggested to try and knock out the mobo material that is blocking the hole.

What are the chances that these holes are actually semi-cut and just "stuck"?

I don't want to try and knock them out thinking they're pre-cut in some way and crack the mobo





That sounds like perfectly horrible advice. The stuff dead mobo's are made of.

I would be far more inclined to try and improvise with the mounting hardware.
Some appropriate sized threaded rod, cut down and screwed into the mounting
holes. Secured with 4 wing nuts would provide the perfect "hard mount" solution.

Just be smart about applying equal and even pressure/tightness. DON'T overtighten.


peace
Wanna
Z77 Extreme6 - i7-3770K @ 4.4 GHz - 8GB GSkill 1866
MSI GTX 970 4GD5T OC - Samsung 850 Pro 128 GB SSD
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.281 seconds.