|
AB350M Pro 4 PC constantly freezing |
Post Reply 
|
Page <12 |
| Author | |
avinicius 
Newbie 
Joined: 28 Jun 2018 Status: Offline Points: 7 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 19 Jul 2018 at 9:07am |
|
AMD Ryzen 5 2400G | ASRock AB350M Pro4 | G.SKILL Ripjaws V @ 3000 MT/s 16-16-16-35 (2x8 GiB) | Seasonic S12II-430
|
|
 |
|
|
kvaism
Newbie
Joined: 17 Jul 2018 Status: Offline Points: 6 |
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jul 2018 at 6:16pm |
|
Seller finally agreed to replaced it,board was faulty. I got a brand new ASUS B350 Plus. Don't waste your time like i did with bios most of these boards are faulty as everyone online says.
|
|
|
|
|
vladafkv
Newbie
Joined: 15 Jul 2018 Status: Offline Points: 14 |
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jul 2018 at 8:11pm |
|
1.01
|
|
|
|
|
MPro4-FAULT
Newbie
Joined: 05 Jun 2018 Status: Offline Points: 24 |
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jul 2018 at 10:45pm |
The MoBo was not having massive issues before the release of Raven or Pinnacle and the BIOS upgrade needed to use them. the 4.X Bios came to get the mb. be compatible with APUs and 2nd gen Ryzen CPU. Using the mature and stable Ryzen 1st gen CPU (not APU support) BIOS with Agesa 1.0.0.6 is the better way to check if the mobo is faulty or is ok, but the new bios behaviour are not well supported. It's possible that the mobo can handle the voltages regarding Ryzen 1st, with no XFR2 and no Vega Cores peaking the same VRM, but can not do properly after flashing the Raven / Pinnacle BIOS due the improvements over Performacen Boost (and Vdroop) and / or the iGPU. Keep in mind that the default voltage of the APU (stock) is 1.40V, peaking 1.55 easily at every moment on load. I think this is much more than the board design was in mind more than a year ago. But you may be configure your 1st gen Ryzen above 1.2V vcore and use the GPU normally, not like the APU does. So this may mean that the weak board may be stable with 1st gen chip because the voltage needings are lower than apus or 2nd gen ryzen. If you still having freezes in this case (1st gen 1.2 + GPU): don't waste more time with wour system configuration, parts, drivers, etc and go for other mobo.
|
|
|
|
|
vladafkv
Newbie
Joined: 15 Jul 2018 Status: Offline Points: 14 |
Post Options
Thanks(0)
Quote Reply
Posted: 25 Jul 2018 at 6:55am |
|
BIOS 4.90 got released today but instead of updating to 4.90 i dowmgraded to 3.30 and my system was stable for full hour. Ryzen 5 1600 btw.
I will test tomorrow when i wake up whole day. :) |
|
|
|
|
vladafkv
Newbie
Joined: 15 Jul 2018 Status: Offline Points: 14 |
Post Options
Thanks(0)
Quote Reply
Posted: 25 Jul 2018 at 11:47pm |
|
3.30 bios
It works fine for 1h 30min after cold boot and then starts restarting. I will downgrade to 3.1 and try it out and then try out 4.90. |
|
|
|
|
vladafkv
Newbie
Joined: 15 Jul 2018 Status: Offline Points: 14 |
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jul 2018 at 8:29am |
|
Restarting on EVERY version of bios.
|
|
|
|
|
konyzulphurea
Newbie
Joined: 12 Jul 2018 Status: Offline Points: 4 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 Jul 2018 at 11:33am |
|
Yes. That's the problem. Before I finally Get a new mobo, I try re-placing CPU, Filling with new thermal Grease (Such as MasterGel nano, or 10W/mK thing), Re-connecting things as Memory, Storage device is no wrong.
|
|
|
|
|
Post Reply
|
Page <12 |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
vladafkv wrote: