Post Windows Installation RAID Setup

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   I have x570 Taichi and 5950x with 1 x nvme with Windows 11 on it, and 2 x matching nvme that I would like to use as RAID0. I'm hoping there is a way to do this without installing windows again, but none of the guides show how to install the drivers post installation.

So far I have followed these instructions:

While the system is booting, press [F2] or [Del] key to enter UEFI setup utility.
2. Go to Advanced\Storage Configuration.
3. Set ?�SATA Controller(s)??to <RAID>.
4. Go to Advanced\AMD PBS and set ?�NVMe RAID mode??to <Enabled >.
5. Go to Boot\CSM and set ?�CSM??to <Disabled>.
6. Press [F10] to save your changes and exit, and then enter the UEFI Setup again.
7. After saving the previously changed settings via [F10] and rebooting the system, the ?�RAIDXpert2
Configuration Utility??submenu becomes available.
Go to Advanced\RAIDXpert2 Configuration Utility\Array Management, and then delete the existing disk
arrays before creating a new array.
Even if you have not configured any RAID array yet, you might have to use ?�Delete Array??first.
Go to Advanced\RAIDXpert2 Configuration Utility\Array Management\Create Array
9A. Select ?�RAID Level??
9B. Select ?�Select Physical Disks??
9C. Change ?�Select Media Type??to ?�SSD??or leave at ?�BOTH??
9D. Select ?�Check All??or enable specific drives that you want to use in the array. Then select ?�Apply
Changes??
Select ?�Create Array??
10. Press [F10] to save to exit.

I have then installed raidexpert2 on windows. Both windows and raid expert don't recognise the array (I'm guessing because of the drivers)

Any suggestions?

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
MasterMirror Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 13 Oct 2023 Status: Offline Points: 40	Post Options Post Reply Quote MasterMirror Report Post Thanks(0) Quote Reply Topic: Post Windows Installation RAID Setup Posted: 13 Oct 2023 at 12:07pm
	I have x570 Taichi and 5950x with 1 x nvme with Windows 11 on it, and 2 x matching nvme that I would like to use as RAID0. I'm hoping there is a way to do this without installing windows again, but none of the guides show how to install the drivers post installation. So far I have followed these instructions: While the system is booting, press [F2] or [Del] key to enter UEFI setup utility. 2. Go to Advanced\Storage Configuration. 3. Set ?�SATA Controller(s)??to <RAID>. 4. Go to Advanced\AMD PBS and set ?�NVMe RAID mode??to <Enabled >. 5. Go to Boot\CSM and set ?�CSM??to <Disabled>. 6. Press [F10] to save your changes and exit, and then enter the UEFI Setup again. 7. After saving the previously changed settings via [F10] and rebooting the system, the ?�RAIDXpert2 Configuration Utility??submenu becomes available. Go to Advanced\RAIDXpert2 Configuration Utility\Array Management, and then delete the existing disk arrays before creating a new array. Even if you have not configured any RAID array yet, you might have to use ?�Delete Array??first. Go to Advanced\RAIDXpert2 Configuration Utility\Array Management\Create Array 9A. Select ?�RAID Level?? 9B. Select ?�Select Physical Disks?? 9C. Change ?�Select Media Type??to ?�SSD??or leave at ?�BOTH?? 9D. Select ?�Check All??or enable specific drives that you want to use in the array. Then select ?�Apply Changes?? Select ?�Create Array?? 10. Press [F10] to save to exit. I have then installed raidexpert2 on windows. Both windows and raid expert don't recognise the array (I'm guessing because of the drivers) Any suggestions?