|
Turbo not working on X299 Fatal1ty i9 XE |
Post Reply 
|
| Author | |
chris719 
Newbie 
Joined: 17 Dec 2017 Status: Offline Points: 11 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Turbo not working on X299 Fatal1ty i9 XEPosted: 17 Dec 2017 at 8:56am |
|
Hello,
I have an i7-7820x and an ASRock X299 Professional Gaming i9 XE and it seems like when everything is set to Auto, the CPU does not go past 3600 MHz no matter how many cores are active. Any thoughts? It seems like Turbo 2.0 and 3.0 do not work at all, but they are enabled in the BIOS. Tried turning on / off TB 2.0/3.0, SpeedStep, SpeedShift, etc. Running Windows 10 with the TB 3.0 application installed and the performance plan set to High Performance with no maximum CPU speed. I wanted to test at stock speeds first before OC, but it seems like the BIOS is unable to use Turbo correctly (Rev 1.0). Thanks, Chris
|
|
 |
|
|
parsec
Moderator Group 
Joined: 04 May 2015 Location: USA Status: Offline Points: 4996 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 Dec 2017 at 10:27am |
|
What program(s) are you using to monitor the core speeds in Windows? Are you running any stress test programs to put a higher load on the CPU? You said everything is set to Auto in the UEFI, do you mean options like CPU Ratio and CPU Mesh Max Ratio? You have Turbo 2.0 and Turbo 3.0 specifically set to enabled, with the others on Auto, correct? Did you try enabling SpeedStep with both Turbo options enabled? Your processor and other Skylake processors have Enhanced SpeedStep that may behave differently with Turbo. Did you run the Turbo 3.0 application in Windows and select/enable the chosen core for the Turbo 3.0 speed of 4.5GHz? Does your CPU and core temperatures seem normal? |
|
|
|
|
|
|
chris719
Newbie
Joined: 17 Dec 2017 Status: Offline Points: 11 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 Dec 2017 at 1:04pm |
|
I used CPU-Z and HWInfo64 to monitor the speeds, both give the same results. I would run the CPU-Z benchmark to exercise all cores and Cinebench in single thread mode to test to see if Turbo 3.0 was working.
Everything related to clocks are set to Auto, so that does include the CPU Ratio and Mesh Max ratio. The CPU does move around in frequency from 1200 to 3600 but still never exceeds 3600, even with just a single threaded task.
I tried enabling SpeedStep with both enabled, I tried Disabled, Native mode, and Out-of-Band mode also for the SpeedShift. The app is running and enabled. I think the app itself works because process affinity does go to the favored core when Cinebench runs. Temps seem normal. It's weird. |
|
|
|
|
GTwannabe
Newbie
Joined: 12 Dec 2017 Status: Offline Points: 5 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 Dec 2017 at 4:06am |
|
Check your FIVR voltage settings. Fiddling with some of the CPU options inserts wonky fixed voltage values in that menu and they do not reset when setting the CPU back to Auto.
I have TB 3.0 working on my 7820X / X299 Taichi. However, it's not behaving properly. Should be: - Max turbo 4.5 on 2 favored cores - 4.3 any core turbo - 4.0 all core turbo Mine is: - Max turbo 4.5 on 2 favored cores (though bounces between 4.5, 4.0, and infrequently 4.1) - 4.0 any core turbo - 4.0 all core turbo - 3.7 AVX workloads (Prime95)
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
chris719 wrote: