Z370 Extreme4 Blackscreen ram don't run at 3200

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   [URL=][/URL]There is a problem, I noticed that the RAM runs only with 2100 (approx.) Instead of 3200.

I had it in A1 and B1, now I read that you should put it in A2 + B2 because several have this problem.

From left to right 1234, 1 A1 2 A2 3 B1 4 B2

Then I just made the bars in A2 and B2, connected everything, etc. and the PC is running all the fans are spinning, LEDs and RGBs work but I get no picture ...

Have also tried only 1 Ram bars or in A2. But nothing works. Have also taken out the mainboard battery and put it back in, power cord removed before and the on / off button on the power supply on / off made etc. Start button held down as no power cable was connected, but I just can not get a picture.

Have else changed the SATA connection to 0, but would have synonymous without hard drive image or get into the BIOS.

What's going on there?

Edited by Marceel - 20 Dec 2017 at 9:35pm

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Marceel Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 20 Dec 2017 Status: Offline Points: 5	Post Options Post Reply Quote Marceel Report Post Thanks(0) Quote Reply Topic: Z370 Extreme4 Blackscreen ram don't run at 3200 Posted: 20 Dec 2017 at 9:33pm
	[URL=][/URL]There is a problem, I noticed that the RAM runs only with 2100 (approx.) Instead of 3200. I had it in A1 and B1, now I read that you should put it in A2 + B2 because several have this problem. From left to right 1234, 1 A1 2 A2 3 B1 4 B2 Then I just made the bars in A2 and B2, connected everything, etc. and the PC is running all the fans are spinning, LEDs and RGBs work but I get no picture ... Have also tried only 1 Ram bars or in A2. But nothing works. Have also taken out the mainboard battery and put it back in, power cord removed before and the on / off button on the power supply on / off made etc. Start button held down as no power cable was connected, but I just can not get a picture. Have else changed the SATA connection to 0, but would have synonymous without hard drive image or get into the BIOS. What's going on there? Edited by Marceel - 20 Dec 2017 at 9:35pm

hansi12 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 11 Dec 2017 Status: Offline Points: 26	Post Options Post Reply Quote hansi12 Report Post Thanks(0) Quote Reply Posted: 21 Dec 2017 at 12:12am
	Have you checked if A1 or B1 still works? Have you done a cmos reset?

Marceel Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 20 Dec 2017 Status: Offline Points: 5	Post Options Post Reply Quote Marceel Report Post Thanks(0) Quote Reply Posted: 21 Dec 2017 at 2:03am
	don't work A1 and B1... I have removed the battery from the board.

Marceel Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 20 Dec 2017 Status: Offline Points: 5	Post Options Post Reply Quote Marceel Report Post Thanks(0) Quote Reply Posted: 21 Dec 2017 at 11:30pm
	with Jumper too... What now? help pls

hansi12 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 11 Dec 2017 Status: Offline Points: 26	Post Options Post Reply Quote hansi12 Report Post Thanks(0) Quote Reply Posted: 22 Dec 2017 at 4:40am
	So it ran before and now it doesnt with the same configuration? It looks like its defective right? Try a minimal setup, or other hardware to rule out the defective parts.