![]() |
New AM5 BIOS updates now available |
Post Reply
|
Page 123 11> |
| Author | |
Kasper058
Newbie
Joined: 20 Nov 2026 Status: Offline Points: 60 |
Post Options
Thanks(0)
Quote Reply
Topic: New AM5 BIOS updates now availablePosted: Yesterday at 12:58am |
|
I installed driver 8.08, but nothing changed. I booted from a Linux flash drive, and everything worked fine?—?the CPU temperature was 40?°C, the frequency was 3.8–4.1, everything was great. It seems like I need to reinstall Windows.
|
|
![]() |
|
Kasper058
Newbie
Joined: 20 Nov 2026 Status: Offline Points: 60 |
Post Options
Thanks(0)
Quote Reply
Posted: 20 Nov 2026 at 8:15pm |
|
Thank you, I’m adjusting the fans via BOIS. The tower has 2 fans, and the quiet mode is selected everywhere. At idle, it’s at 1000 RPM; during a stress test, it reaches 75 degrees and 1600–1700 RPM. I’ll try setting the chipset version to 8.08 and resetting the power settings in Windows.
|
|
![]() |
|
Xaltar
Moderator Group
Joined: 16 May 2015 Location: Europe Status: Offline Points: 44588 |
Post Options
Thanks(0)
Quote Reply
Posted: 20 Nov 2026 at 7:20pm |
|
Are you setting your fan curves through the OS or relying on the BIOS settings?
If you are doing so through the OS then the higher temps + windows power scheme not working would lean me towards an issue in communication between the OS and the BIOS since the update. It may be worth trying a live linux distro off a flash drive and checking temps there. If temps check out under linux then you can try waiting for the next AMD chipset version to go up, it should be in the next week or so by AMD's track record. You can also try going to version 8.08 as some people have had issues with the current latest. So long as your load temps are not abnormally high it won't be an issue. I suspect the latest AGESA has made some changes to power states and fan control. This will almost certainly be addressed by AMD either in the next AGESA (BIOS) or via the chipset drivers. I should also note, the issue doesn't seem to be effecting everyone and it also isn't limited to ASRock boards and the 4.60 BIOS. This leads me to believe it is an AGESA related quirk that effects certain configurations but not all. Let me know how it goes and thanks for bringing this to my attention. Edited by Xaltar - 20 Nov 2026 at 7:22pm |
|
|
|
![]() |
|
Kasper058
Newbie
Joined: 20 Nov 2026 Status: Offline Points: 60 |
Post Options
Thanks(0)
Quote Reply
Posted: 20 Nov 2026 at 5:31pm |
|
The driver is the latest version, 8.09.28.1124. I reinstalled it, but that didn’t solve the problem. I always set the fan speed for air cooling manually and consistently, and previously, with these settings, the temperature at idle was 40. I also noticed that the power scheme in Windows seems to be not working?—?no matter what mode I select, the CPU temperature at idle is always 50. I reset the BIOS, but that didn’t help either. If I go into the BIOS, the CPU temperature there is 40–42.
|
|
![]() |
|
Xaltar
Moderator Group
Joined: 16 May 2015 Location: Europe Status: Offline Points: 44588 |
Post Options
Thanks(0)
Quote Reply
Posted: 20 Nov 2026 at 5:06pm |
|
It seems the new AGESA that 4.60 is based on makes some changes to the fan control
portion of the BIOS. I have seen a few people reporting issues with their AIO water cooling. The solution for them was to swap the pump from the pump/DC header to a normal fan header and set the fan speed to 100%. I am guessing this isn't your issue however as I suspect you are using air cooling. If you have not already done so, update your AMD Chipset drivers. It sounds like windows isn't handling your power states correctly. Quite often BIOS updates will coincide with Chipset driver updates that set things up properly for the new AGESA version (AMD). Let me know if that helps. If not, check your fan profiles in BIOS, they were most likely changed. You may want to set them to a higher preset, normal vs silent for example. |
|
|
|
![]() |
|
Kasper058
Newbie
Joined: 20 Nov 2026 Status: Offline Points: 60 |
Post Options
Thanks(0)
Quote Reply
Posted: 20 Nov 2026 at 3:25pm |
|
Hi, does anyone have this issue? After updating the BIOS on the B850 Riptide to version 4.60, the temperature of the 7500F processor in idle mode has risen to 50 degrees, and the processor frequency is stuck at 4.5 GHz. Previously, the temperature was around 40 degrees in idle mode
|
|
![]() |
|
Xaltar
Moderator Group
Joined: 16 May 2015 Location: Europe Status: Offline Points: 44588 |
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2026 at 5:20am |
|
Glad to hear it worked
|
|
|
|
![]() |
|
crankz
Newbie
Joined: 11 Sep 2026 Status: Offline Points: 30 |
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2026 at 5:10am |
|
ye flashback worked after a few tries. i needed to convert the usb to mbr and format as fat 16k. just formating as fat no 16k or using as it was (gpt) was failing flashback
thanks for the help tho |
|
![]() |
|
Xaltar
Moderator Group
Joined: 16 May 2015 Location: Europe Status: Offline Points: 44588 |
Post Options
Thanks(0)
Quote Reply
Posted: 11 Sep 2026 at 11:50am |
|
Have you tried BIOS flashback? Page 53 of your user manual, page 57 in the
PDF version from your product page, explains the process. Edited by Xaltar - 11 Sep 2026 at 11:50am |
|
|
|
![]() |
|
crankz
Newbie
Joined: 11 Sep 2026 Status: Offline Points: 30 |
Post Options
Thanks(0)
Quote Reply
Posted: 11 Sep 2026 at 8:50am |
|
Not sure if its the right place but since i cant start a post...
Ive always been able to update/downgrade my B850 LIVEMIXER BIOS but since i went from 4.43(latest) to 3.50 i can only flash bios versions olders than the one i have... Ive tried diferent USB Sticks, flashback, clear CMOS, using C:... nothing works unless its an older version... Using 3.26 atm Anyone else has been through this? |
|
![]() |
|
Post Reply
|
Page 123 11> |
| Tweet |
| Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |