ASRock.com Homepage
Forum Home Forum Home > Technical Support > AMD Motherboards
  New Posts New Posts RSS Feed - Asrock taichi and flare x issue
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

Asrock taichi and flare x issue

 Post Reply Post Reply Page  <12
Author
Message
TooQik View Drop Down
Newbie
Newbie


Joined: 06 Apr 2017
Location: Australia
Status: Offline
Points: 104
Post Options Post Options   Thanks (0) Thanks(0)   Quote TooQik Quote  Post ReplyReply Direct Link To This Post Posted: 30 May 2017 at 4:56pm
If you're still running the 2.34 beta BIOS try and reset all your settings to default via the BIOS, reboot and let it boot fully into Windows. Check your timings once in Windows to make sure it's defaulted back to 2133 etc.

Reboot your PC, go into the BIOS, select a XMP profile in OC Tweaker and then Save and Exit. Let it boot into Windows again.

Hopefully this works for you.

Back to Top
Nocturnal View Drop Down
Newbie
Newbie
Avatar

Joined: 21 Mar 2017
Status: Offline
Points: 37
Post Options Post Options   Thanks (0) Thanks(0)   Quote Nocturnal Quote  Post ReplyReply Direct Link To This Post Posted: 30 May 2017 at 5:55pm
I want to add - reset CMOS - boot to win. Then switch off fully your PSU from wall (coldboot), clear CMOS one more and then you can try change memory settings in BIOS.
Back to Top
AlbinoRhino View Drop Down
Newbie
Newbie
Avatar

Joined: 28 Apr 2017
Status: Offline
Points: 153
Post Options Post Options   Thanks (0) Thanks(0)   Quote AlbinoRhino Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2017 at 5:55pm
This isn't limited to the Taichi. I couldn't get the Flare X's to go above 2933 on my Killer SLI A/C. Trident Z's wouldn't do it either.

From the looks of it the Bioses are pretty similar so it will just be a waiting game.
Back to Top
jedi86694 View Drop Down
Newbie
Newbie
Avatar

Joined: 29 May 2017
Location: Qc
Status: Offline
Points: 7
Post Options Post Options   Thanks (0) Thanks(0)   Quote jedi86694 Quote  Post ReplyReply Direct Link To This Post Posted: 04 Jun 2017 at 11:54pm
Hello everyone, after so much testing I put to this board I managed to figure out one of the flare X 3200 was kinda defective as it would not run two ram sticks at 3200 speeds..

I switched to 1 stick and immediately it loaded 3200 speed with xmp 1 with 1.35 stock voltage.

not contented with only one stick, I returned the sticks and got the flare X 2400mhz.. I tried it with the new agesa bios 1.0.0.6    (2.34) It ran stable at 3200mhz and even 3330
timings are a bit relaxed at 20 19 19 19 55, with 1.35 volts

here is where the problem sets up.. Running multiple times of cinebench decreases the scores gradually since the bios  is in beta and not fully stable..

so I downgraded to the official 2.30 which I am currently testing at 2993 mhz because 3200 wont budge
settings are 20 20 20 20 40 , 1.35 volts 1.02500 soc,

any suggestions regarding my settings? should I keep the beta bios? thanks
Back to Top
 Post Reply Post Reply Page  <12
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 1.563 seconds.