ASRock.com Homepage
Forum Home Forum Home > Technical Support > AMD Motherboards
  New Posts New Posts RSS Feed - Hyper Quad M.2 Card Performance?
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

Hyper Quad M.2 Card Performance?
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
bvalente View Drop Down
Newbie
Newbie


Joined: 05 Sep 2018
Status: Offline
Points: 9 		Post Options Post Options   Thanks (0) Thanks(0)   Quote bvalente Quote  Post ReplyReply Direct Link To This Post Topic: Hyper Quad M.2 Card Performance?
    Posted: 02 Mar 2020 at 11:03am
It seems my hyper quad m2 raid array is pretty slow?

seq read 4747 seq write 6115 (as measured by crystaldiskmark)

https://www.dropbox.com/s/sgqamkrc86zii97/crystaldisk.png?dl=0


this is 4x 1tb Intel 660p M2 cards in a raid 0 configuration


I have seen specs of similar setups that are 115304 seq read

doesn't have to match, but seems like it could be much faster?

I'm pretty sure I have the firmware configured correctly, the card is in slot 3.


the swap disks i have set up on the raid array are a constraint to performance on some of my most important apps

Any feedback, suggestions, questions would be great thank you!


Brian
Back to Top
cx5 View Drop Down
Senior Member
Senior Member


Joined: 15 Sep 2017
Location: Hong Kong
Status: Offline
Points: 2398 		Post Options Post Options   Thanks (0) Thanks(0)   Quote cx5 Quote  Post ReplyReply Direct Link To This Post Posted: 02 Mar 2020 at 3:06pm
Hello Brian,

seq read 4747ï¼?sounds too low, should be this link multiply 4 = 7000Mb/s
https://cdn.mos.cms.futurecdn.net/zY4mMsbYdA4JUC3ayDKGUm-970-80.png


seq write 6115, sounds about right to me,

because 660p is slow, only around 1700mb/s,
https://cdn.mos.cms.futurecdn.net/FRZi4HbetMXCawprZFMsab-970-80.png
so 4 card is 7000.

If you get a HP EX950, write is 2900Mb/s then 4 card raid-0 is around 11000Mb/s

those guys with very high transfer are using very fast NVMe like HP EX950
x370taichi@3.50gen4
AX750 Optane900P SN770
3800x PosdonZro4 BarrowPWM-17w>420x140x28
XFX SWFT319 6900XT
MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz
Back to Top
gizmic View Drop Down
Groupie
Groupie
Avatar

Joined: 13 Jun 2018
Location: Hong Kong
Status: Offline
Points: 677 		Post Options Post Options   Thanks (1) Thanks(1)   Quote gizmic Quote  Post ReplyReply Direct Link To This Post Posted: 02 Mar 2020 at 6:21pm
actually quad raid 0 are closer to 3X performance
Back to Top
bvalente View Drop Down
Newbie
Newbie


Joined: 05 Sep 2018
Status: Offline
Points: 9 		Post Options Post Options   Thanks (0) Thanks(0)   Quote bvalente Quote  Post ReplyReply Direct Link To This Post Posted: 02 Mar 2020 at 11:48pm
Thanks - is that 3x performance of?

Brian
Back to Top
stonewater View Drop Down
Newbie
Newbie


Joined: 03 Apr 2020
Status: Offline
Points: 2 		Post Options Post Options   Thanks (0) Thanks(0)   Quote stonewater Quote  Post ReplyReply Direct Link To This Post Posted: 03 Apr 2020 at 12:47am
So I just tried installing 4 x Seagate Firecuda 520's in RAID 0 on the Hyper Quad and I'm getting writes topping out at 3.89GBps and reads at 5.22GB/s which looks suspiciously to me like PCI4.

This is on a TRX40 Taichi which comes with the hyper quad - in the ASrock recommended PCIE4.

Did anyone else experience this / solve this?

Thanks

David
Back to Top
stonewater View Drop Down
Newbie
Newbie


Joined: 03 Apr 2020
Status: Offline
Points: 2 		Post Options Post Options   Thanks (0) Thanks(0)   Quote stonewater Quote  Post ReplyReply Direct Link To This Post Posted: 03 Apr 2020 at 12:48am
Of course I meant 'suspiciously like PCI3'.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.078 seconds.