x370 pro gaming aquantia lan issue |
Post Reply | Page <1234> |
Author | |
ajlueke
Newbie Joined: 07 Jun 2017 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
Hello all,
I was also having substantial issues using the AQuantia port with the X370 Fatal1ty Professional Gaming motherboard. The port would get stuck verifying my internet connection and I would be unable to resolve it. If I switched to Wifi, it would connect, but the throughput was extremely slow. This occurred consistently on my old Trendnet TEW-639GR router. When I upgraded to an ASUS AC3100 the issue was resolved, and it also has not reoccurred since. I have not upgraded my AQauntia drivers to the latest, and have been running fine with no issues since November 2017. I did make sure to configure the IPV6 settings in the new router, as my ISP supports those. The old router was not IPV6 capable. Not sure if that was part of the problem or not, but in my experience, there was definitely some sort of handshaking problem with the AQuantia port and my old router. Edited by ajlueke - 30 May 2018 at 11:34pm |
|
EvanWasHere
Newbie Joined: 29 May 2018 Status: Offline Points: 4 |
Post Options
Thanks(0)
|
How is the 10GbE on your motherboards working out? I bought the ASRock FATAL1TY a few months ago and finally just bought another one, so I could use 10GbE with a switch between them. But my transfers between machines have been slower than the 1Gb NICs and I am constantly having issues with Netflix and webpages. I tried the newest drivers as well as the one suggested here.
Edited by EvanWasHere - 29 May 2018 at 6:37am |
|
UberPizius
Newbie Joined: 27 Jul 2017 Location: Italy Status: Offline Points: 11 |
Post Options
Thanks(0)
|
z270 supercarrier here and other 5gbit lan problems
the 5gbit lan refuses to work, if i enable on the bios, and install the latest driver at restart the pc froze on error 46 and A2, to get it work i nedd to power off the pc and restart, after i disable del 5bg lan on the bios the pc works normally after doing a memtest on my g skill trident Z rgb 3200MHZ i found 2 error, the ram was mounted in slot 2-4, then i have done a memtest in the slot 1-3, this time no error -__- testing a single module of crucial ddr4 2400mhz no error was found dismounted and reomunted the cpu, all is fine socket is ok, and cpu contact is good, cooler not overtightened now i'm replacing the ram with another kit, but for the 5gbit lan? is the mainboard defective? |
|
p1r473
Newbie Joined: 20 May 2017 Status: Offline Points: 6 |
Post Options
Thanks(0)
|
Unfortunately this driver isnt the cause of my freezes... got to keep digging
|
|
jpopcorn
Newbie Joined: 30 Apr 2017 Location: Henderson, NV Status: Offline Points: 10 |
Post Options
Thanks(0)
|
Sonic, thank you for your post and the driver link. I've been testing those new drivers, 1.40.42.0. So far so good.
Before those latest drivers, my 5G LAN was causing all sorts of problems. So I RMA'ed my board. The new board had the same 5G issue. Again, now that 5G LAN is working. Thank you.
|
|
p1r473
Newbie Joined: 20 May 2017 Status: Offline Points: 6 |
Post Options
Thanks(0)
|
I was getting the same thing- I couldn't reach cineplex.com website on previous firmware (intel NIC worked, Aquantia didnt). I upgraded to the latest and it fixed it.
HOWEVER, for the last 3 days I have been getting computer freezes every hour. Nothing in the event manager so far, until last time (event posted below). I am going to disable Aquantia LAN and see if it fixes my freezing. Has anyone else experienced freezing with Aquantia LAN 1.40.42.0? Really hard to debug a freeze. I have to manually power off. No crash dump or anything, total freeze. I did manage to trigger a freeze plugging in and unplugging the ethernet cable. BTW I am on ASRock Z270 SuperCarrier mobo Here is the event: Aquantia AQtion 5Gbit Network Adapter (NDIS 6.50 Miniport) : Has determined that the network adapter is not functioning properly. Aquantia AQtion 5Gbit Network Adapter (NDIS 6.50 Miniport) : The network adapter has detected that the token ring cable is disconnected from the network adapter. Please reconnect the cable. The network interface "Aquantia AQtion 5Gbit Network Adapter (NDIS 6.50 Miniport)" has begun resetting. There will be a momentary disruption in network connectivity while the hardware resets. Reason: The network driver detected that its hardware has stopped responding to commands. This network interface has reset 24 time(s) since it was last initialized. Edited by p1r473 - 29 May 2017 at 1:24pm |
|
Ivan_83
Newbie Joined: 22 May 2017 Status: Offline Points: 85 |
Post Options
Thanks(0)
|
Set fixed 1Gb port speed instead auto in Aquantia nic settings.
My guess that Aquantia try to auto negotiate 5Gb speed, but fail. |
|
Kevin A
Newbie Joined: 02 May 2017 Location: East Coast USA Status: Offline Points: 94 |
Post Options
Thanks(0)
|
Thanks for the Aquantia link(now bookmarked), I've downloaded the new driver and will give it a shot.
|
|
MisterJ
Senior Member Joined: 19 Apr 2017 Status: Offline Points: 1097 |
Post Options
Thanks(0)
|
Thanks, SoniC. This must the public portal I was told about when I was e-mailing Aquantia. Great, now we have an official source of their drivers! Enjoy, John.
|
|
SoniC
Newbie Joined: 23 May 2017 Status: Offline Points: 183 |
Post Options
Thanks(2)
|
P.S. ASRock support replied me this today:
please update to latest Aquantia LAN driver 1.40.42.0
from: http://www.aquantia.com/driver-download/ And afterwards the install procedure... Nice for the Support to catch up to the latest driver versions too... Anyway - it basically confirms what I am testing / feeling since 18 Hours+ on Aquantia now = with 1.40.42.0 drivers it actually works... And it works kinda better than intel I211 (might be a placebo though).
|
|
-=SoniC=-
TR x1950, ASRock X399 FPG (v. 3.33A), G.Skill 3200 CL14 64GB, Enermax LiqTech 280, AMD Vega 64 LC, 10x HDDs (mostly Hitachi), 2x M.2 (970EVO,960Pro), Xonar DX, AX1200i PSU |
|
Post Reply | Page <1234> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |