![]() |
X399 Fatal1ty not booting with code 62 |
Post Reply ![]() |
Page <1234> |
Author | |
alexmaz ![]() Newbie ![]() Joined: 03 Feb 2018 Status: Offline Points: 25 |
![]() ![]() ![]() ![]() ![]() |
Sticks seems fine because they all work in the A nd B slots. Installing the CPU was a painfull process because of the screws 2 and 2 not taking. I'll try to redo it, but the pc works fine aside not seeing the ram, I installed Windows and it works fine.
|
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
Say what? ![]() |
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
You won't like this. I know I know. That Kit is on ASRocks Memory QVL. But, it isn't on G.Skills Compatabilty List for your board. No X399 boards from any manuf. http://www.gskill.com/en/configurator?manu=52&chip=3073&model=3075 I've seen this happen before. It's kinda rare. It comes from early motherboard pre-release in-house BIOSes. BIOSes with rev's of like 0.27. Have a friend with some mem on G.Skills link I presented above? To test? |
|
![]() |
|
alexmaz ![]() Newbie ![]() Joined: 03 Feb 2018 Status: Offline Points: 25 |
![]() ![]() ![]() ![]() ![]() |
No I don't know anyone with those rams. I can try to send them back to Amazon and get something else, but I can't rule out that the motherboard might be faulty. It doen't see the sticks in C and D even if they are the only one installed. |
|
![]() |
|
alexmaz ![]() Newbie ![]() Joined: 03 Feb 2018 Status: Offline Points: 25 |
![]() ![]() ![]() ![]() ![]() |
If I move again the graphic card to the first PCIe slot, the system doesn't boot. I don't know what to think.
|
|
![]() |
|
kerberos_20 ![]() Senior Member ![]() ![]() Joined: 06 Dec 2017 Location: czech republic Status: Offline Points: 3657 |
![]() ![]() ![]() ![]() ![]() |
![]() |
|
alexmaz ![]() Newbie ![]() Joined: 03 Feb 2018 Status: Offline Points: 25 |
![]() ![]() ![]() ![]() ![]() |
I'll check tomorrow, now it's 4 am here and I really need some sleep, I spent abut 10 hours on this
![]() Is it possible to have some bent pins and still have the system working fine aside those 2 issues?
|
|
![]() |
|
kerberos_20 ![]() Senior Member ![]() ![]() Joined: 06 Dec 2017 Location: czech republic Status: Offline Points: 3657 |
![]() ![]() ![]() ![]() ![]() |
each pin has its own functions...its hard to say that
but since u dont have error post codes but instead system freezes during initialisation, then something isnt connected right |
|
![]() |
|
JayB33 ![]() Newbie ![]() Joined: 04 Dec 2017 Status: Offline Points: 69 |
![]() ![]() ![]() ![]() ![]() |
Take photos so we can see :)
|
|
![]() |
|
alexmaz ![]() Newbie ![]() Joined: 03 Feb 2018 Status: Offline Points: 25 |
![]() ![]() ![]() ![]() ![]() |
The system is stable, I'm posting from it. The only problems are: - there is no way it sees the ram sticks in the C and D sockets. If I install only 1 or 2 sticks there, it's doesn't post. I don't remeber which codes gives in this case, I'll check again. - the system won't post if the graphic card is in the first pci-e slot, I tried 2 cards. In this case the code is 62. I'll remove the cooler and the cpu and check.
|
|
![]() |
Post Reply ![]() |
Page <1234> |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |