Failed update BIOS on conroexfire-esata2

Author

Message

Topic Search

Topic Options

youthMP

Newbie

Joined: 24 Jul 2015
Location: Madeira
Status: Offline
Points: 5

Post Options

Post Reply

Quote youthMP

Report Post

Thanks(0)

Quote

Topic: Failed update BIOS on conroexfire-esata2
Posted: 24 Jul 2015 at 8:41am

Hey all, today I found a little problem upgrading my BIOS motherboard which model is "conroexfire-esata2" in order to improve development. I successfully installed the software which I downloaded from ASrock website but then when I rebooted my computer It was 'bricked' , after windows loading menu appears it all went blue screen and just won't move it from there.

I tried removing battery from motherboard and put it again and nothing happened. By the way I'm no computer geek so I would like some Info about what should I do in order to restore BIOS and the normal function of the motherboard.

Thank you for your attention,

Looking forward for an awnser,

Bernardo Reis.

odiebugs

Newbie

Joined: 07 Jul 2015
Status: Offline
Points: 193

Post Options

Post Reply

Quote odiebugs

Report Post

Thanks(0)

Quote

Posted: 24 Jul 2015 at 9:45am

Welcome to the board.

If you bricked the BIOS, you wouldn't see anything, and never windows logo, I think you've caused a windows problem.

I don't know what your BIOS version was, but the last three had a specific reason to update, and unless you needed them you shouldn't have upgraded.

Remove the hard drive, and try booting and going into the BIOS, look at the storage settings as change as needed .

If you can enter it, it's not bricked.

Now I would attach the hard drive and reboot and enter BIOS and check boot drive settings.

If windows doesn't boot, try using the windows disk and repair windows.

Edited by odiebugs - 24 Jul 2015 at 9:46am

asrocking

Xaltar

Moderator Group

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 25073

Post Options

Post Reply

Quote Xaltar

Report Post

Thanks(0)

Quote

Posted: 24 Jul 2015 at 12:37pm

Am I correct in understanding that the system froze at the windows boot screen after the bios flash and then would no longer post after the error?

The first thing I would try in your situation is a full CMOS clear

1. Disconnect the power cord

2. Press the power button and hold it until all lights on the motherboard go out

3. Place the clear CMOS jumper in the clear CMOS position

4. Remove the CMOS battery

5. Leave the system like this for at least 4 hours

6. Replace the CMOS battery

7. Put the clear CMOS jumper back to its default position (pins 1 and 2)

8. Reconnect the power cord

9. Power up the system

If I am understanding you correctly the system posted after the bios flash and then only after the freeze failed to post, hopefully it was the result of some corrupt settings in the bios post flash, in which case the clear CMOS step above should correct it.

Good luck

youthMP

Newbie

Joined: 24 Jul 2015
Location: Madeira
Status: Offline
Points: 5

Post Options

Post Reply

Quote youthMP

Report Post

Thanks(1)

Quote

Posted: 25 Jul 2015 at 12:42am

Thanks Xaltar I will now proceed to your resolution and see if it works. Yes odiebugs, I can enter into the bios when the system runs and don't blackscreen, but still I don't know properly how to work with the menus. As I could understand what your suggesting is formatting the computer but I wouldn't like to loose all the data stored so I will try first Xaltar suggestion. Thank you both for your attention.

Bernardo Reis

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
youthMP Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 24 Jul 2015 Location: Madeira Status: Offline Points: 5	Post Options Post Reply Quote youthMP Report Post Thanks(0) Quote Reply Topic: Failed update BIOS on conroexfire-esata2 Posted: 24 Jul 2015 at 8:41am
	Hey all, today I found a little problem upgrading my BIOS motherboard which model is "conroexfire-esata2" in order to improve development. I successfully installed the software which I downloaded from ASrock website but then when I rebooted my computer It was 'bricked' , after windows loading menu appears it all went blue screen and just won't move it from there. I tried removing battery from motherboard and put it again and nothing happened. By the way I'm no computer geek so I would like some Info about what should I do in order to restore BIOS and the normal function of the motherboard. Thank you for your attention, Looking forward for an awnser, Bernardo Reis.

odiebugs Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 07 Jul 2015 Status: Offline Points: 193	Post Options Post Reply Quote odiebugs Report Post Thanks(0) Quote Reply Posted: 24 Jul 2015 at 9:45am
	Welcome to the board. If you bricked the BIOS, you wouldn't see anything, and never windows logo, I think you've caused a windows problem. I don't know what your BIOS version was, but the last three had a specific reason to update, and unless you needed them you shouldn't have upgraded. Remove the hard drive, and try booting and going into the BIOS, look at the storage settings as change as needed . If you can enter it, it's not bricked. Now I would attach the hard drive and reboot and enter BIOS and check boot drive settings. If windows doesn't boot, try using the windows disk and repair windows. Edited by odiebugs - 24 Jul 2015 at 9:46am
	asrocking

Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 25073	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Posted: 24 Jul 2015 at 12:37pm
	Am I correct in understanding that the system froze at the windows boot screen after the bios flash and then would no longer post after the error? The first thing I would try in your situation is a full CMOS clear 1. Disconnect the power cord 2. Press the power button and hold it until all lights on the motherboard go out 3. Place the clear CMOS jumper in the clear CMOS position 4. Remove the CMOS battery 5. Leave the system like this for at least 4 hours 6. Replace the CMOS battery 7. Put the clear CMOS jumper back to its default position (pins 1 and 2) 8. Reconnect the power cord 9. Power up the system If I am understanding you correctly the system posted after the bios flash and then only after the freeze failed to post, hopefully it was the result of some corrupt settings in the bios post flash, in which case the clear CMOS step above should correct it. Good luck

youthMP Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 24 Jul 2015 Location: Madeira Status: Offline Points: 5	Post Options Post Reply Quote youthMP Report Post Thanks(1) Quote Reply Posted: 25 Jul 2015 at 12:42am
	Thanks Xaltar I will now proceed to your resolution and see if it works. Yes odiebugs, I can enter into the bios when the system runs and don't blackscreen, but still I don't know properly how to work with the menus. As I could understand what your suggesting is formatting the computer but I wouldn't like to loose all the data stored so I will try first Xaltar suggestion. Thank you both for your attention. Bernardo Reis